20839219 Volvo.Penta Retainer

Table 1
Event Code    
Code and Description     Conditions which Generate this Code     System Response    
E016(3) High Engine Coolant Temperature Shutdown     The engine coolant temperature has exceeded the trip point and the delay time has expired.     The code is logged.
The engine will be shutdown in 15 seconds.    
E017(1) High Engine Coolant Temperature Warning     The engine coolant temperature has exceeded the trip point and the delay time has expired.     The code is logged.    
110-0 High Coolant Temperature Warning     The engine coolant temperature has exceeded the trip point and the delay time has expired.     The code is logged.
The diagnostic lamp will flash.
The alarm lamp will illuminate.    
110-0 High Coolant Temperature Warning (Derate)     The engine coolant temperature has exceeded the trip point and the delay time has expired.     The code is logged.
The diagnostic lamp will flash.
The alarm lamp will illuminate.
The engine is derated to a map dependent value.    
110-11 Very High Coolant Temperature (Derate)     The engine coolant temperature has exceeded the trip point and the delay time has expired.     The code is logged.
The diagnostic lamp will flash.
The alarm lamp will flash.
The engine is derated to a map dependent value.    
110-11 Very High Coolant Temperature (Shutdown)     The engine coolant temperature has exceeded the trip point and the delay time has expired.     The code is logged.
The engine will be shutdown after 20 seconds.    Probable Causes
Low coolant level and/or coolant leakage
Water temperature regulator and/or pressure relief valve
Air in cooling system
Radiator or heat exchanger
Engine cooling fan (if equipped)
Coolant pump
Coolant temperature sensor
Load on the systemRecommended Actions
Coolant
Personal injury can result from hot coolant, steam and alkali.At operating temperature, engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot coolant or steam. Any contact can cause severe burns.Remove filler cap slowly to relieve pressure only when engine is stopped and radiator cap is cool enough to touch with your bare hand.Cooling System Conditioner contains alkali. Avoid contact with skin and eyes.
Inspect the coolant level. If necessary, add coolant.
Check the mixture of antifreeze and water. Refer to Operation and Maintenance Manual.
Check the cooling system for leaks. Repair any leaks immediately.
Check for air in the cooling system. Refer to Systems Operation/Testing and Adjusting for the correct procedure.Water Temperature Regulator and/or Pressure Relief Valve
Pressure test the cooling system. Refer to Systems Operation/Testing and Adjusting for the correct procedure.
Check that the seating surfaces of the pressure relief valve and the radiator cap are clean and undamaged.
Check operation of the pressure relief valve and/or the water temperature regulator. If necessary, clean the components and/or replace the components.Air in Cooling System
Check for air in the cooling system. Air can enter the cooling system in different ways. The following conditions cause air in the cooling system:
Filling the cooling system incorrectly
Combustion gas leakage into the cooling systemCombustion gas can get into the system through the following conditions: internal cracks, damaged cylinder head and damaged cylinder head gasket.Radiator or Heat Exchanger
Check the radiator fins for dirt, debris, and/or damage. Remove any dirt and/or debris and straighten any bent fins. Check for collapsed hoses and/or other restrictions.
Check the radiator for internal blockage. Refer to Systems Operation/Testing and Adjusting for more information.
Check for sufficient flow and temperature of the cooling water through the heat exchanger. If the flow of cooling water through the heat exchanger is insufficient, determine the location of the obstruction. If the temperature of the cooling water is too high, determine the cause. Make the necessary repairs.Faulty Engine Cooling Fan (if equipped)
If the fan is belt driven, check for loose drive belts. A loose fan drive belt will cause a reduction in the air flow across the radiator. Check the fan drive belt for proper belt tension. Adjust the tension of the fan drive belt, if necessary. Refer to Operation and Maintenance Manual.
Check the fan clutch, if equipped. A fan clutch or a hydraulic driven fan that is not turning at the correct speed can cause improper air speed across the radiator core. The lack of proper air flow across the radiator core can cause the coolant not to cool to the proper temperature differential.Coolant Pump
Inspect the impeller of the coolant pump for damage and/or erosion.
Make sure that the drive gear is not loose on the drive shaft of the coolant pump.
If necessary, replace the coolant pump. Refer to Disassembly and Assembly for the correct procedure.Check the Coolant Temperature Sensor and/or the Circuit
Check the reading of the coolant temperature on Cat ET. The temperature should rise steadily as the engine is warmed. Ensure that the temperature is reasonable.If the reading on Cat ET for the coolant temperature is not reasonable, troubleshoot the circuit and the coolant temperature sensor. Refer to Troubleshooting, "Sensor Signal (Analog, Active) - Test".Load on the system
Check that the engine is not loaded beyond design.