20805516 Rocker arm shaft Volvo.Penta
TAD550GE; TAD551GE; TAD750GE, TAD750VE; TAD760VE
Rocker
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$11.99
19-09-2023
-: -
UMIRIKO Car Trash Can Fresh Style Floral Hanging Car Garbage Bin Foldable, Leak-Proof, Waterproof S 20805516
SIZE: S: 8.66 x 8.66 x 5.9 INCH and M: 11 x 11 x 5.9 INCH || LEAK-PROOF AND WATERPROOF: This car trash can is made of Oxford cloth, which is waterproof. The interior is supported by a PE board, which makes the trash can more three-dimensional and stable, and can be placed on the floor of the car. || FOLDABLE AND HANGING: The trash can has an adjustable shoulder strap, which can be hung on the back of the seat. With a fixed snap, it can fix the garbage bag and prevent the garbage bag from being transferred into the trash can. It can be folded and stored when not in use. || MULTI-FUNCTIONAL: The waterproof and leak-proof car dumpster can store a variety of items, and can also store garbage bags. Keep the inside of your car neat and clean. || EASY WIPE AND REUSABLE: The inner layer is hot-pressed with PEVA material, Wipe or rinse to keep the trash can clean.
SIZE: S: 8.66 x 8.66 x 5.9 INCH and M: 11 x 11 x 5.9 INCH || LEAK-PROOF AND WATERPROOF: This car trash can is made of Oxford cloth, which is waterproof. The interior is supported by a PE board, which makes the trash can more three-dimensional and stable, and can be placed on the floor of the car. || FOLDABLE AND HANGING: The trash can has an adjustable shoulder strap, which can be hung on the back of the seat. With a fixed snap, it can fix the garbage bag and prevent the garbage bag from being transferred into the trash can. It can be folded and stored when not in use. || MULTI-FUNCTIONAL: The waterproof and leak-proof car dumpster can store a variety of items, and can also store garbage bags. Keep the inside of your car neat and clean. || EASY WIPE AND REUSABLE: The inner layer is hot-pressed with PEVA material, Wipe or rinse to keep the trash can clean.
$10.99
17-05-2023
-: -
UMIRIKO Tire Covers Waterproof Fresh Style Floral Spare Wheel Tire Covers 30'' for RV Trailer SUV Truck Camper Travel Trailer Accessories 20805516
[Four Sizes]: S: Diameter 24.41in Suitable for diameters 23-25.5 inches. M: Diameter 26.38in is suitable for 25.5-27.5 inches. L: Diameter 28.35in is suitable for 27.5-29.5 inches. XL: Diameter 30.71in is suitable for 29.5-31.4 inches. The width of each size wheel well is 9.8 inches. || [High-quality Material]: Made of silver-coated Oxford fabric, which has sun protection function, reduces the damage caused by the sun and protects the tires. || [Waterproof and Dustproof]: The fabric is waterproof, reducing the damage caused by dogs peeing on the tires, rain or other substances, and avoiding the shortening of the service life of the tires. A spare tire placed in the yard, using this tire cover can prevent leaves, mud, etc. from getting stuck in the wheel. || [Easy to install]: With elastic band and hook design, better wrapping, easy to install, and increase the stability of use. || [WIDE APPLICATIONS]: Perfectly compatible with tires for trailers, RVs, SUVs, trucks and many other models.
[Four Sizes]: S: Diameter 24.41in Suitable for diameters 23-25.5 inches. M: Diameter 26.38in is suitable for 25.5-27.5 inches. L: Diameter 28.35in is suitable for 27.5-29.5 inches. XL: Diameter 30.71in is suitable for 29.5-31.4 inches. The width of each size wheel well is 9.8 inches. || [High-quality Material]: Made of silver-coated Oxford fabric, which has sun protection function, reduces the damage caused by the sun and protects the tires. || [Waterproof and Dustproof]: The fabric is waterproof, reducing the damage caused by dogs peeing on the tires, rain or other substances, and avoiding the shortening of the service life of the tires. A spare tire placed in the yard, using this tire cover can prevent leaves, mud, etc. from getting stuck in the wheel. || [Easy to install]: With elastic band and hook design, better wrapping, easy to install, and increase the stability of use. || [WIDE APPLICATIONS]: Perfectly compatible with tires for trailers, RVs, SUVs, trucks and many other models.
$10.99
19-09-2023
-: -
UMIRIKO Car Registration and Insurance Holder Leather Fresh Style Floral Vehicle Glove Box Organizers, Case for Essential Documents, Driver License and Cards Car Essentials 20805516
[Leather Material]: soft and delicate, durable, wear-resistant, thin and gorgeous. || [Six Pockets]: This car registration and insurance holder is roomy and measures 9.5" x 5". There is 1 large pocket for important documents such as car insurance policies. 2 pockets for vehicle registration cards and 3 small pockets for driver's license or other valuable cards. || [Clear Pocket]: The internal card slot is made of transparent pvc material, and all documents can be easily seen after opening. || [GIFT]: The car document organizer with exquisite fashion patterns, maybe a good gift for yourself, lover, friends and family. || [FUN DESIGNS]: Our car registration and insurance clips come in many different fun designs, there is sure to be a favorite. Fits perfectly in your glove box or center console and is ideal for protecting important documents.
[Leather Material]: soft and delicate, durable, wear-resistant, thin and gorgeous. || [Six Pockets]: This car registration and insurance holder is roomy and measures 9.5" x 5". There is 1 large pocket for important documents such as car insurance policies. 2 pockets for vehicle registration cards and 3 small pockets for driver's license or other valuable cards. || [Clear Pocket]: The internal card slot is made of transparent pvc material, and all documents can be easily seen after opening. || [GIFT]: The car document organizer with exquisite fashion patterns, maybe a good gift for yourself, lover, friends and family. || [FUN DESIGNS]: Our car registration and insurance clips come in many different fun designs, there is sure to be a favorite. Fits perfectly in your glove box or center console and is ideal for protecting important documents.
Number on catalog scheme: 27
Compatible models:
TAD550GE; TAD551GE; TAD750GE
TAD750VE; TAD760VE
Volvo.Penta
Volvo Penta entire parts catalog list:
- Cylinder Head » 20805516
Information:
Start By:a. remove cylinder head assembly and spacer plateb. remove oil pan platec. remove oil pump1. Remove the carbon ring and lip from the inner surface of the cylinder liner. 2. Turn the crankshaft until two of the pistons are at bottom center. Remove the nuts and bolts (1) from the connecting rods that are at bottom center. Remove connecting rod caps (2), and put identification marks on them for installation purposes.
Do not let the connecting rods hit the crankshaft or the bottom edge of the cylinder liners when the pistons are removed.
3. Push the connecting rods and pistons away from the crankshaft until the piston rings are out of the cylinder liners. Remove the two pistons from the engine.4. Keep each connecting rod cap with its respective connecting rod and piston. Put identification marks on each piston as to its location in the engine.5. Do Steps 1 through 4 for the removal of the remaining pistons. The following steps are for the installation of the pistons and connecting rods.6. Turn the crankshaft until the bearing journals for the pistons to be installed are at bottom center.7. Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and the connecting rod bearings.8. Move the piston rings on the pistons until the ring openings are approximately 90° apart. 9. Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the "V" mark on the cylinder block. Put tooling (A) in position on the cylinder block and compress the piston rings.10. Push the piston into the cylinder liner and out of the ring compressor. 11. Pull the connecting rod into position on the crankshaft as shown. Install connecting rod bolts (1) in the connecting rods.12. Put clean engine oil on the lower half of the connecting rod bearing. Put 2P2506 Thread Lubricant on the bolt threads and on the surfaces of the nuts that make contact with the connecting rod caps.
When the connecting rod caps are installed, make sure the number on the side of the cap is next to, and respective with, the number on the side of the connecting rod.
13. Install connecting rod caps (2) and the nuts that hold them. Tighten the nuts to a torque of 40 4 N m (30 3 lb.ft.). Put a mark on each nut as to its location, and tighten them 90° more.14. Do Steps 6 through 13 for the remainder of the pistons.End By:a. install oil pumpb. install oil pan platec. install cylinder head assembly and spacer plateDisassemble Pistons And Connecting Rods
Start By:a. remove pistons and connecting rods 1. Remove the rings from the pistons with tool (A). 2. Remove retaining ring (3), piston pin (1) and connecting rod (2) from the piston.3. Clean the piston ring grooves on the old piston with an acceptable ring groove tool.4. See, Use Of Piston Pin Bearing Removal And Installation Tools, Special Instruction, Form No. SMHS7295, for more information about removal and installation of piston pin bearings. Be sure to remove the bearings from the crankshaft end of connecting rod.5. Heat the connecting rod in an oven to a temperature of 177° to 260° C (350° to 500° F). Never use a direct flame to heat a connecting rod. 6. Put 6V3029 Spacer (11) in the base plate. Put the connecting rod on the base plate of tooling (B).7. Put the connecting rod piston pin bearing end in the center of the port assembly of tooling (B). Install pin (6) in the center of the bore of the connecting rod bearing.8. Install 6V2049 Adapter (9). Put the hole in the adapter in alignment with the hole in the base plate of tooling (B).9. Install clamp bar (10) and clamp pin (7). The old bearing is pushed out by tooling (B) as the new bearing is installed.10. Put 5P8645 Pusher Adapter (8) in position, as shown, with the taper side down. The piston pin bearing joint must be in alignment with the hole in adapter (9) and the base plate of tooling (B).11. Put pusher (4) on adapter (8).12. Use tooling (B) to push the new piston pin bearing (5) into the connecting rod until adapter (8) of tooling (B) makes full contact with the connecting rod surface.13. Remove the connecting rod and the old piston pin bearing from tooling (B).14. Check the piston pin bearing bore diameter after the bearing is installed. The correct dimension is 43.210 0.008 mm (1.7012 .0003 in.). The maximum permissible clearance between the bearing and piston pin (worn) must not be more than 0.08 mm (.003 in.).Assemble Pistons And Connecting Rods
1. Install connecting rod (2) in the piston with the bearing tab groove (slot) (12) on the same side as the cutout (depression) (13) on the head of the piston.2. Install piston pin (1) and retaining rings (3) in the piston.3. When old pistons are to be used, clean the piston grooves with an acceptable piston groove cleaning tool. 4. Install the spring for the oil ring. Install the oil ring with tool (A). The gap in the ring must be approximately 180° from the ring spring connections.5. The two compression rings have marks "UP-1" and "UP-2". The rings must be installed with these marks toward the top of the piston with "UP-1" as the top ring. After installation of all three piston rings, put piston rings in position so the gaps in rings are 120° apart. Compression rings that do not have identification can be installed either way.6. To check the clearance between the piston ring grooves and rings, see Specifications.7. See Specifications to check the clearance between the ends of the piston rings (end gap).End By:a. install pistons and connecting rods
Do not let the connecting rods hit the crankshaft or the bottom edge of the cylinder liners when the pistons are removed.
3. Push the connecting rods and pistons away from the crankshaft until the piston rings are out of the cylinder liners. Remove the two pistons from the engine.4. Keep each connecting rod cap with its respective connecting rod and piston. Put identification marks on each piston as to its location in the engine.5. Do Steps 1 through 4 for the removal of the remaining pistons. The following steps are for the installation of the pistons and connecting rods.6. Turn the crankshaft until the bearing journals for the pistons to be installed are at bottom center.7. Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and the connecting rod bearings.8. Move the piston rings on the pistons until the ring openings are approximately 90° apart. 9. Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the "V" mark on the cylinder block. Put tooling (A) in position on the cylinder block and compress the piston rings.10. Push the piston into the cylinder liner and out of the ring compressor. 11. Pull the connecting rod into position on the crankshaft as shown. Install connecting rod bolts (1) in the connecting rods.12. Put clean engine oil on the lower half of the connecting rod bearing. Put 2P2506 Thread Lubricant on the bolt threads and on the surfaces of the nuts that make contact with the connecting rod caps.
When the connecting rod caps are installed, make sure the number on the side of the cap is next to, and respective with, the number on the side of the connecting rod.
13. Install connecting rod caps (2) and the nuts that hold them. Tighten the nuts to a torque of 40 4 N m (30 3 lb.ft.). Put a mark on each nut as to its location, and tighten them 90° more.14. Do Steps 6 through 13 for the remainder of the pistons.End By:a. install oil pumpb. install oil pan platec. install cylinder head assembly and spacer plateDisassemble Pistons And Connecting Rods
Start By:a. remove pistons and connecting rods 1. Remove the rings from the pistons with tool (A). 2. Remove retaining ring (3), piston pin (1) and connecting rod (2) from the piston.3. Clean the piston ring grooves on the old piston with an acceptable ring groove tool.4. See, Use Of Piston Pin Bearing Removal And Installation Tools, Special Instruction, Form No. SMHS7295, for more information about removal and installation of piston pin bearings. Be sure to remove the bearings from the crankshaft end of connecting rod.5. Heat the connecting rod in an oven to a temperature of 177° to 260° C (350° to 500° F). Never use a direct flame to heat a connecting rod. 6. Put 6V3029 Spacer (11) in the base plate. Put the connecting rod on the base plate of tooling (B).7. Put the connecting rod piston pin bearing end in the center of the port assembly of tooling (B). Install pin (6) in the center of the bore of the connecting rod bearing.8. Install 6V2049 Adapter (9). Put the hole in the adapter in alignment with the hole in the base plate of tooling (B).9. Install clamp bar (10) and clamp pin (7). The old bearing is pushed out by tooling (B) as the new bearing is installed.10. Put 5P8645 Pusher Adapter (8) in position, as shown, with the taper side down. The piston pin bearing joint must be in alignment with the hole in adapter (9) and the base plate of tooling (B).11. Put pusher (4) on adapter (8).12. Use tooling (B) to push the new piston pin bearing (5) into the connecting rod until adapter (8) of tooling (B) makes full contact with the connecting rod surface.13. Remove the connecting rod and the old piston pin bearing from tooling (B).14. Check the piston pin bearing bore diameter after the bearing is installed. The correct dimension is 43.210 0.008 mm (1.7012 .0003 in.). The maximum permissible clearance between the bearing and piston pin (worn) must not be more than 0.08 mm (.003 in.).Assemble Pistons And Connecting Rods
1. Install connecting rod (2) in the piston with the bearing tab groove (slot) (12) on the same side as the cutout (depression) (13) on the head of the piston.2. Install piston pin (1) and retaining rings (3) in the piston.3. When old pistons are to be used, clean the piston grooves with an acceptable piston groove cleaning tool. 4. Install the spring for the oil ring. Install the oil ring with tool (A). The gap in the ring must be approximately 180° from the ring spring connections.5. The two compression rings have marks "UP-1" and "UP-2". The rings must be installed with these marks toward the top of the piston with "UP-1" as the top ring. After installation of all three piston rings, put piston rings in position so the gaps in rings are 120° apart. Compression rings that do not have identification can be installed either way.6. To check the clearance between the piston ring grooves and rings, see Specifications.7. See Specifications to check the clearance between the ends of the piston rings (end gap).End By:a. install pistons and connecting rods
Parts rocker Volvo Penta:
20805512
20805520
21242550
21242533
21294973
20792876
20792878
20794124