806620 Volvo.Penta Roller bearing

Table 1
Diagnostic Trouble Codes
J1939 Code and Description Conditions that Generate the Code System Response
5576-2 Aftertreatment #1 Identification Number Module: Erratic, Intermittent, or Incorrect The Clean Emissions Module (CEM) is not a certified match with the engine.
Diagnostic code 5576-8 is not active.
No 3510 diagnostic codes are active.
The Electronic Control Module (ECM) has been powered for 2 seconds.
“This is a violation of the emissions regulations, and may result in severe fines and/or legal action if not corrected immediately.” Do not operate the engine with the active fault. Engine power is derated.
The code is logged.
5576-8 Aftertreatment #1 Identification Number Module: Abnormal Frequency Pulse Width or Period No signal is detected from the aftertreatment identification module.
No 3510 diagnostic codes are active.
The ECM has been powered for 2 seconds.
Do not continue to operate the engine with the active fault. The code is logged.
Engine power is derated.
5576-14 Aftertreatment #1 Identification Number Module: Special Instruction The signal from the aftertreatment identification module is invalid.
Diagnostic code 5576-8 is not active.
The ECM has been powered for 2 seconds.
Do not continue to operate the engine with the active fault. The code is logged.
Engine power is derated.
5577-2 Aftertreatment #2 Identification Number Module: Erratic, Intermittent, or Incorrect The installed CEM is not a certified match with the engine.
Diagnostic code 5577-8 is not active.
No 3510 diagnostic codes are active.
The ECM has been powered for 2 seconds.
“This is a violation of the emissions regulations, and may result in severe fines and/or legal action if not corrected immediately.” Do not operate the engine with the active fault. Engine power is derated.
The code is logged.
5577-8 Aftertreatment #2 Identification Number Module: Abnormal Frequency Pulse Width or Period No signal is detected from the aftertreatment identification module.
No 3510 diagnostic codes are active.
The ECM has been powered for 2 seconds.
Do not continue to operate the engine with the active fault. The code is logged.
Engine power is derated.
5577-14 Aftertreatment #2 Identification Number Module: Special Instruction The signal from the aftertreatment identification module is invalid.
Diagnostic code 5577-8 is not active.
The ECM has been powered for 2 seconds.
Do not continue to operate the engine with the active fault. The code is logged.
Engine power is derated. The aftertreatment identification module sends a digital signal to the engine ECM in order to ensure that the correct CEM is installed to the engine.If more than 25 hours (total operating hours) have been accumulated on the engine, the aftertreatment identification module will cease to send the signal. The diagnostic codes that are listed in Table 1 will be disabled.
Illustration 1 g02231895
Schematic for the aftertreatment identification module
Test Step 1. Check for Active Diagnostic Codes
Establish communication between the Caterpillar Electronic Technician (ET) and the ECM.
Download the "Product Summary Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes. Results:
Active 5576-2 or 5577-2 - A 5576-2 or 5577-2 diagnostic code is active. Proceed to Test Step 4.
Active 5576-8 or 5577-8 - A 5576-8 or 5577-8 diagnostic code is active. Proceed to Test Step 2.
Active 5576-14 or 5577-14 - A 5576-14 or 5577-14 diagnostic code is active. Proceed to Test Step 4.Test Step 2. Inspect the Electrical Connectors and the Wiring
Illustration 2 g02133313
Location of the components for the aftertreatment identification module
(1) CEM identification plate
(2) Aftertreatment identification module
Illustration 3 g02231881
Location of the connectors for the aftertreatment identification modules
(3) Aftertreatment #2 identification module
(4) Aftertreatment #1 identification module
(5) J2/P2 ECM connector
Thoroughly inspect the connector for the aftertreatment identification modules (3) and (4). Also, thoroughly inspect the J2/P2 ECM connector (5). Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 4 g02156576
Terminal locations at the P2 ECM connector for the aftertreatment identification module
(P2-65) Signal for the aftertreatment identification module #2
(P2-73) Signal for the aftertreatment identification module #1
(P2-82) Return
(P2-92) Analog supply
Illustration 5 g01994856
Terminal locations at the connector for the aftertreatment identification module
(Terminal 1) Analog supply
(Terminal 3) Aftertreatment identification module
(Terminal 6) Return
Perform a 45 N (10 lb) pull test on each of the wires in the connectors that are associated with the aftertreatment identification module.
Check the torque of the allen head screw on each of the ECM connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness for abrasion and pinch points from the aftertreatment identification module back to the ECM. Expected Result:All of the connectors, pins, and sockets are coupled and/or inserted and the harness and wiring are free of corrosion, abrasion, and pinch points.Results:
OK - All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points. Proceed to Test Step 3.
Not OK - There is a problem with the connectors and/or wiring.Repair: Repair the connectors or the harness and/or replace the connectors or the harness. Ensure that all of the seals are correctly in place and ensure that the connectors are coupled.Use Cat ET to clear all logged diagnostic codes and then verify that the repair has eliminated the fault.STOPTest Step 3. Measure the Supply Voltage at the Connector for the Aftertreatment Identification Module
Turn the keyswitch to the OFF position.
Disconnect the aftertreatment identification module from the harness.
Turn the keyswitch to the ON position.
Measure the voltage at the plug for the aftertreatment identification module from the ter