243066 Rotor Volvo.Penta
MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A
Rotor
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$30.79
29-08-2017
Reliable S: Reliable Supply
Bulb for CODMAN & SHURTLEFF 243066 LAMP 12VOLTS 35WATTS
35 WATTS||12 VOLTS||MR16 SHAPE||3300 COLOR TEMPERATURE
35 WATTS||12 VOLTS||MR16 SHAPE||3300 COLOR TEMPERATURE
Compatible models:
MD100A; TMD100A; TMD100AK
MD120A; MD120AK; TMD120A
Volvo.Penta
Volvo Penta entire parts catalog list:
- Alternator » 243066
Information:
Assembly Procedure (Horizontally Mounted Particulate Filter)
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    
B     1S-0258     Plastic Hammer As     1    Note: When the sections are installed, maintain the original direction of the flow of exhaust. The sections must maintain the original direction of the flow of exhaust in order to comply with emissions standards.
Illustration 1 g01458222
Note: Install new gasket. Refer to Special Instructions, "Procedure for cleaning ash from the Diesel Particulate Filter (DPF)".
Position the new gasket (not shown) and connect inlet section (9) onto filter section (7) .
Position the new gasket (not shown) and connect outlet section (6) onto filter section (7) .
Install band clamps (8) and hand tighten the band clamps.
Align the marks at Point (E) on the filter section and the exterior of the inlet and outlet sections.
Use Tooling (B) in order to tap gently band clamps (8) around the diesel particulate filter in one full rotation. This process is used to seat the band clamps.Note: Verify that sections (6) , (7) , and (9) remain in original positions.
Position band clamps (8) into original positions. Tighten band clamps (8) to a torque of 11 1 N m (100 10 lb in).
Illustration 2 g01454590
Apply Tooling (A) to the threads on fittings (3) , (4) , and (5) .
Install fittings (5) and tighten the fittings to a torque of 24 4 N m (208 35 lb in).
Position temperature sensor (2) into the original position.
Tighten fitting (3) to a torque of 45 5 N m (33 4 lb ft). Repeat this step for the opposite side.
Tighten fitting (4) to a torque of 8 2 N m (71 18 lb in). Repeat this step for the opposite side.
Illustration 3 g01458162
Position clamps (1) , as shown. Tighten clamps (1) to a torque of 8.5 1 N m (75 10 lb in).
Reset the engine ash model. Refer to the section "Ash Service Reset".Assembly Procedure (Vertically Mounted Particulate Filter)
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    
B     1S-0258     Plastic Hammer As     1    Note: When the sections are installed, maintain the original direction of the flow of exhaust. The sections must maintain the original direction of the flow of exhaust in order to comply with the emissions standards.
Illustration 4 g01460747
Note: Install new gasket. Refer to Special Instructions, "Procedure for cleaning ash from the Diesel Particulate Filter (DPF)".
Position the new gasket (not shown) and connect inlet section (18) onto filter section (11) .
Install band clamp (19) and hand tighten the band clamp.
Position mounting assemblies (16) and clamp assemblies (17) at Point (H) .
Tighten clamp assemblies (17) to a torque of 11 1 N m (100 10 lb in).
Illustration 5 g01459892
Note: Install new gasket. Refer to Special Instructions, "Procedure for cleaning ash from the Diesel Particulate Filter (DPF)".
Position the new gasket (not shown) and connect outlet section (15) onto filter section (11) .
Install band clamp (12) and hand tighten the band clamp.
Position mounting assembly (14) and clamp assembly (13) at Point (G) .
Tighten clamp assembly (13) to a torque of 11 1 N m (100 10 lb in).
Illustration 6 g01460767
Align the marks at Point (F) on filter section (11) , inlet section (18) , and outlet section (15) .
Use Tooling (B) in order to tap gently band clamps (19) and (12) around the diesel particulate filter in one full rotation. This process is used to seat the band clamps.Note: Verify that sections (18) , (11) , and (15) remain in original positions.
Position band clamps (19) and (12) into original positions. Tighten the band clamps to a torque of 11 1 N m (100 10 lb in).
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    
B     1S-0258     Plastic Hammer As     1    Note: When the sections are installed, maintain the original direction of the flow of exhaust. The sections must maintain the original direction of the flow of exhaust in order to comply with emissions standards.
Illustration 1 g01458222
Note: Install new gasket. Refer to Special Instructions, "Procedure for cleaning ash from the Diesel Particulate Filter (DPF)".
Position the new gasket (not shown) and connect inlet section (9) onto filter section (7) .
Position the new gasket (not shown) and connect outlet section (6) onto filter section (7) .
Install band clamps (8) and hand tighten the band clamps.
Align the marks at Point (E) on the filter section and the exterior of the inlet and outlet sections.
Use Tooling (B) in order to tap gently band clamps (8) around the diesel particulate filter in one full rotation. This process is used to seat the band clamps.Note: Verify that sections (6) , (7) , and (9) remain in original positions.
Position band clamps (8) into original positions. Tighten band clamps (8) to a torque of 11 1 N m (100 10 lb in).
Illustration 2 g01454590
Apply Tooling (A) to the threads on fittings (3) , (4) , and (5) .
Install fittings (5) and tighten the fittings to a torque of 24 4 N m (208 35 lb in).
Position temperature sensor (2) into the original position.
Tighten fitting (3) to a torque of 45 5 N m (33 4 lb ft). Repeat this step for the opposite side.
Tighten fitting (4) to a torque of 8 2 N m (71 18 lb in). Repeat this step for the opposite side.
Illustration 3 g01458162
Position clamps (1) , as shown. Tighten clamps (1) to a torque of 8.5 1 N m (75 10 lb in).
Reset the engine ash model. Refer to the section "Ash Service Reset".Assembly Procedure (Vertically Mounted Particulate Filter)
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    
B     1S-0258     Plastic Hammer As     1    Note: When the sections are installed, maintain the original direction of the flow of exhaust. The sections must maintain the original direction of the flow of exhaust in order to comply with the emissions standards.
Illustration 4 g01460747
Note: Install new gasket. Refer to Special Instructions, "Procedure for cleaning ash from the Diesel Particulate Filter (DPF)".
Position the new gasket (not shown) and connect inlet section (18) onto filter section (11) .
Install band clamp (19) and hand tighten the band clamp.
Position mounting assemblies (16) and clamp assemblies (17) at Point (H) .
Tighten clamp assemblies (17) to a torque of 11 1 N m (100 10 lb in).
Illustration 5 g01459892
Note: Install new gasket. Refer to Special Instructions, "Procedure for cleaning ash from the Diesel Particulate Filter (DPF)".
Position the new gasket (not shown) and connect outlet section (15) onto filter section (11) .
Install band clamp (12) and hand tighten the band clamp.
Position mounting assembly (14) and clamp assembly (13) at Point (G) .
Tighten clamp assembly (13) to a torque of 11 1 N m (100 10 lb in).
Illustration 6 g01460767
Align the marks at Point (F) on filter section (11) , inlet section (18) , and outlet section (15) .
Use Tooling (B) in order to tap gently band clamps (19) and (12) around the diesel particulate filter in one full rotation. This process is used to seat the band clamps.Note: Verify that sections (18) , (11) , and (15) remain in original positions.
Position band clamps (19) and (12) into original positions. Tighten the band clamps to a torque of 11 1 N m (100 10 lb in).
Parts rotor Volvo Penta:
847704
847704 Rotor
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AQD70D; TAMD70D; TAMD70E, MD120A; MD120AK; TMD120A, MD31A; TMD31A; TMD31B, MD40A; TMD40A; TMD40B, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD16
825923
825923 Rotor
AQ115A; AQ115B; AQ130, AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD1B; MD2B; AQD2B, MD6; MD6A; MD6B, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B
827040
827040 Rotor
AQ115A; AQ115B; AQ130, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD21B; AQD21B, MD40A; TMD40A; TMD40B, MD70B; MD70BK; TMD70B, MD70
236874
236874 Rotor
AQD70D; TAMD70D; TAMD70E, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, TMD100C, TMD121C; TAMD121C; TAMD121D
422658
467412
827577
240458
240458 Rotor
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, TD100CHC; TD100CRC; TD121CHC, TD100G; TD100G-85; TD100G-87, TD120AHC; TD120ARC; TAD120AHC, TD120C, TID120FPP; TID120FG; TD12