22726669 Volvo.Penta Rubber moulding

Table 1
Typical Configuration Parameters    
Parameter    Programmability    
"Air shutoff"     Yes    
CAT "Datalink #2 identifier"     Yes    
"Crank duration"     Yes    
"Crank terminate speed"     Yes    
"Cold cylinder cutout"     Yes    
"Cooldown speed"     Yes    
ECM serial number     No    
"Engine acceleration rate"     Yes    
"Engine cooldown duration"     Yes    
"Engine cooling system" (1)     Yes    
"Engine prelube duration"     Yes    
"Engine rated speed"     Software dependent    
"Engine rotation"     Software dependent    
"Engine serial number"     Yes    
Equipment ID     Yes    
"Ether control"     Yes    
Fuel correction factor     Yes    
"Fuel ratio control"     Yes    
"Low idle"     Yes    
"Maximum number of crank cycles"     Yes    
"Personality Module Part Number"     Software dependent    
"Personality module release date"     Software dependent    
"Rated fuel position"     Yes    
"Total fuel"     Yes    
"Total hours"     Yes    
"Total tattletale"     No    
( 1 ) Jacket water aftercooling or separate circuit aftercoolingThe following parameters are programmed at the factory to "0":
"Crank Duration"
"Maximum Number Of Crank Cycles"The "0" settings prevent the Electronic Control Module (ECM) from engaging the starting motors. The settings must be reprogrammed before the engine will crank.Ensure that the "Air Shutoff" and the "Ether Control" parameters are "Enabled/ON" (if equipped). If the engine does not have these options, ensure that these two parameters are "DISABLED/OFF".If the engine is equipped with Prelube, the "Engine Prelube Duration" must be programmed to a value that is greater than "0" seconds. Otherwise, the prelube pump will not cycle. If the engine is not equipped with Prelube, the parameter must be programmed to "0".The engine has separate circuit aftercooling. The correct configuration of the aftercooling system must be programmed.No password is required for programming a new ECM during the first 100 hours of service life. This 100 hour "free configuration" feature enables the customer to tailor the programmable setpoints to the requirements of the installation. Exceptions are "Fuel Limit" and "Personality Module Mismatch".Air Shutoff (If Equipped)
Illustration 1 g01271448
Air shutoffThe air shutoff is activated by oil pressure. The air shutoff uses a moving plate to block inlet air to the engine. The engine stops because of the restricted air supply to the combustion chamber. The air shutoff will actuate for the following conditions:
The emergency stop button is pressed.
The air shutoff is activated.
An overspeed shutdown occurs.
The electronic control module loses power.Note: A switch may be supplied by the customer in order to activate the air shutoffs.The air shutoff must be manually reset before the engine is restarted. To reset the air shutoff, use a ratchet to rotate operating shaft (2) until the shaft latches in the "OPEN" position.Power to the ECM must be cycled in order to restart the engine. Turn the battery disconnect switch to the OFF position for three seconds. Turn the battery disconnect switch back to the ON position. The engine may now be restarted.Cold Cylinder Cutout
Note: This feature can be enabled or disabled with an electronic service tool.The Cold Cylinder Cutout feature provides the following benefits:
Reduction of white smoke during cold starting
Reduction of the duration of advanced timing (cold mode)
Reduction of ether injectionThe ECM automatically turns off one electronic unit injector at a time during the following occurrences:
Cold start-up
Extended time at low idleThe ECM monitors the change of the fuel rack in order to determine if a cylinder is firing. If the cylinder is firing the ECM activates the electronic unit injector. If the cylinder is not firing the electronic unit injector remains deactivated. This reduces white smoke.The following conditions must be met in order to activate the Cold Cylinder Cutout:
The Cold Cylinder Cutout parameter is programmed to "ENABLE".
The fuel rack is less than 13 mm (.5 inch).
The jacket water coolant temperature is less than 63 °C (145 °F).The Cold Cylinder Cutout strategy is activated under either of the following conditions:
Ten seconds after the engine reaches the low idle rpm
Three seconds after ether injection is completedThe following conditions will deactivate the Cold Cylinder Cutout:
The Cold Cylinder Cutout parameter is programmed to "DISABLED".
The jacket water temperature is more than 70 °C (158 °F).
An ET service tool is used for the cold cylinder cutout test.
The ether injection system is used.
The coolant temperature sensor has failed.
The engine is operating at a certain rpm when the Cold Cylinder Cutout is activated. If the engine rpm then varies by more than 50 rpm, the feature is deactivated for three seconds. A new engine speed is established when the feature is reactivated.
The engine is at low idle rpm for ten seconds. If the engine speed is then reduced by more than 50 rpm, the Cold Cylinder Cutout is deactivated for 30 seconds.
If the fuel rack is greater than 13 mm (.5 inch), the Cold Cylinder Cutout is deactivated for one second.Ether Control
Note: This is an optional feature.The ECM automatically injects ether into the air inlet manifold when the following conditions are met:
The engine rpm is between 75 and 400 rpm.