241116 Screw Volvo.Penta
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B
Screw
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$10.39
05-06-2024
0.1388[0.06] Pounds
CN: zhu993xiao
Luejnbogty 13Pcs Frame Caps Set Frame Hole Cover Plug for R1200Gs Lc R 1200Gs R 1200 Gs Adventure 2013 2014 2015 2016
Luejnbogty Material: Plastic || Condition: || Color : Black || Comes in a set of 13 pieces
Luejnbogty Material: Plastic || Condition: || Color : Black || Comes in a set of 13 pieces
$10.90
05-06-2024
0.1433[0.06] Pounds
CN: Xuantaidingwangluo
13Pcs Set Hole Cover Plug for R1200Gs Lc R 1200Gs R 1200 Gs 2013 2014 2015 2016
Doumneou Material: Plastic || Condition: || Color : Black || Comes in a 13 pieces
Doumneou Material: Plastic || Condition: || Color : Black || Comes in a 13 pieces
Compatible models:
Volvo Penta entire parts catalog list:
D100BHC; D100BRC; TD100AHC; TD100ARC
D120A; D120AK; TD120A; TD120AG; TD120AG PP; TD120AK
D70B; D70B PP; D70B K; TD70B
MD100A; TMD100A; TMD100AK; TMD100A-CC; MD100B; MD100BK; MD100B-CC
MD120A; MD120AK; TMD120A; TMD120AK; TAMD120A; TAMD120AK; TMD120B; TAMD120B; TAMD120B-CC
MD70B; MD70BK; TMD70B; THAMD70B; TAMD70B; AQD70BL; AQD70B
Information:
Illustration 1 g01359958
Schematic for the CAN data link
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01360079
Connector locations for the CAN data link (typical left side rear engine view)
(1) Engine interface connector
(2) Service tool connector
(3) P1 ECM connector
Thoroughly inspect connectors (1), (2), and (3). Inspect all of the connectors that are associated with the CAN data link. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01209797
Terminals at the P1 ECM connector that are associated with the CAN data link
(P1-34) CAN data link −
(P1-42) CAN shield
(P1-50) CAN data link +
Illustration 4 g01360095
Terminals at the engine interface connector that are associated with the CAN data link
(P1-16) CAN shield
(P1-17) CAN data link +
(P1-18) CAN data link −
Illustration 5 g01209794
Terminals at the service tool connector that are associated with the CAN data link
(Terminal C) CAN shield
(Terminal F) CAN data link +
(Terminal G) CAN data link −
Illustration 6 g01355248
Terminals at the connector for the termination resistor that are associated with the CAN data link
(Terminal A) CAN data link +
(Terminal B) CAN data link −
(Terminal C) CAN shield
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
Check the allen head screw on each ECM connector and on the customer connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the wiring harnesses for abrasion, for corrosion and for pinch points. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring harness.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 2. Verify the Proper Installation of the Termination Resistors
Remove the electrical power from the ECM.
Disconnect the display panel from the data link.
Disconnect the Caterpillar Electronic Technician (ET) from the service tool connector.
Disconnect the P1 ECM connector. Note: Wiggle the harness during the following measurements in order to reveal an intermittent condition.
Measure the resistance between terminals P1-50 (CAN Data Link +) and P1-34 (CAN Data Link -). Expected Result:The resistance is between 57 and 63 Ohms.Results:
OK - The resistance is between 57 and 63 Ohms. Proceed to Test Step 3.
Not OK - The resistance is between 114 Ohms and 126 Ohms. A termination resistor is missing.Repair: Verify that two termination resistors are connected to the data link. One resistor must be located on each end of the data link. The engine is shipped with one termination resistor that is installed between the ECM and the customer connector.Refer to the appropriate electrical schematic in order to determine the missing resistor. Replace the missing resistor. Verify that the problem is resolved.STOP
Not OK - The resistance is less than 57 Ohms. There may be a short circuit in the harness. Proceed to Test Step 3.
Not OK - The resistance is greater than 126 Ohms. There may be an open circuit in the harness. Proceed to Test Step 4.Test Step 3. Check the Harness for a Short Circuit
Remove both termination resistors from the CAN data link.
Disconnect the display panel.
Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Table 1
Resistance Measurements for the CAN Data Link
Connector and Terminal Terminal
P1-50 (CAN data link +) All of the other terminals on the P1 connector
Engine ground
P1-34 (CAN data link -) All of the other terminals on the P1 connector
Engine ground Expected Result:Each check of the resistance indicates an open circuit.Results:
OK - Each check of the resistance indicates an open circuit. The harness is not shorted. Proceed to Test Step 4.
Not OK - At least one check of the resistance does not indicate an open circuit.Repair: There is a short circuit in a harness. There may be a problem with a connector. Repair the wiring and/or the connector. Replace part, if necessary. Verify that the problem is resolved.STOPTest Step 4. Check the Harness for an Open Circuit
Remove both termination resistors from the CAN data link.
Fabricate a jumper wire that is long enough to create a test circuit across the connector for the termination resistor. Crimp connector sockets to each end of the jumper wire.
Use the jumper wire in order to create a short circuit between terminals A and B on the tee's connector for the termination resistor that is located between the P1 ECM connector and the customer connector. This will effectively replace the termination resistor with a short circuit.
Measure the r
Parts screw Volvo Penta:
417464
417464 Screw
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, T
827562
827562 Screw kit
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD40A; TMD40A; TMD40B, MD6; MD6A; MD6B, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, T
242736
242736 Screw
AQD70D; TAMD70D; TAMD70E, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, TMD100C, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
244218
244218 Screw
AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, DH10A; DH10A 285; DH10A 360, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAD1230G; TD1
959452
823279
823279 Screw
D100BHC; D100BRC; TD100AHC, MD100A; TMD100A; TMD100AK, TAMD103A, TD100CHC; TD100CRC; TD121CHC, TMD100C, TMD102A; TAMD102A; TAMD102D
824075
101152