840152 Volvo.Penta Screw

Personal injury can result from failure to disconnect the battery.First, disconnect the negative battery cable. Then, disconnect the positive battery cable.A positive power lead can cause sparks if the battery is not disconnected. Sparks can possibly result in battery explosion or fire.
Use the following procedure to disassemble brush plate from the starting motor:
Remove vehicle leads connected to the starter, noting positions for reinstallation of starter, and remove starter.
Remove the solenoid lead from the ground stud in the CE housing, noting position of the ground stud or mark the CE housing & frame for reassembly.
Remove the six CE screws.
Illustration 1 g06348460
Remove the three plugs from the frame to allow removing the three field leads to positive brushes attaching screws for 12V, 24V & 32V models or two field leads to positive brushes attaching screws for 64V models.
Illustration 2 g06348466
Remove the CE housing and armature assembly as a unit. It is best to remove them together to keep the brushes contained.
If only replacing the brushes, remove the remaining brush screws and contain in that position with the brush springs to release the armature. Go to step 5 in assembly procedures.
From the insulated/ground terminal, carefully noting orientation for reassembly, remove all remaining hardware. Check the condition of insulators and sealing features and consider replacing. If insulators and sealing are damaged or excessively worn.
Remove the three brush plate to CE housing attaching screws and remove brush plate.Cleaning Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use the following procedure to clean electric starting motor brush:
It is recommended that the brush plate assembly and CE frame be separated for a thorough cleaning, being careful not to damage the aramid paper (white) insulator or grommet for the insulated/ground terminal.Note: Do not use air pressure to remove dust from inside the frame.
Illustration 3 g06348977
Using a low-pressure source of air, blow the brush dust out of CE frame and the brush assembly. It may be necessary to use a screw driver or similar device to remove all the carbon (hardened brush dust).
Illustration 4 g06348512
It may also be necessary to scrape the hardened dust from the four recessed holes that are on the back side of the brush holder assembly. These recessed holes are for the threaded ends of the ground brush holders.
Illustration 5 g06348518
Thoroughly examine the brush plate for chunks of hardened brush dust that could become grounded and carefully remove. The fiber insulators at the base of the insulated brush holders are an area that may need some cleaning. Remove the hardened brush dust all around the outside edge of these insulators.
Illustration 6 g06348525
Any cleaning inside the frame should be done with a nylon brush or cloth.Assembly Procedure
Use the following procedure to assemble brush plate to starting motor:
Place the insulator paper in between brush-plate assembly and the CE housing.
Place the two insulator washers and rubber bushing on the ground stud at the brush-plate.
Attach the brush-plate assembly to the insulator paper on the CE with the three attaching screws. Torque the screws to 1.92 to 3.95 N m (17.00 to 35.00 lb in).
Place the plastic insulator, flat washer, lock-washer, and nut on the ground stud. Torque the nut to 27.12 N m (240.03 lb in).
Replace the brushes and contain them in the upward position with the brush springs. Place the armature inside the brush holder cavity and release the brushes onto it. If only replacing the brushes, another option is to replace the brushes one at a time on the brush plate and CE assembly by pulling the spring to allow them to get into the holder, assuring the same position as removed and the armature is in place. Torque the brush screws to 2.26 to 4.52 N m (20.00 to 40.00 lb in) for punched holes or 3.62 to 5.20 N.m (32.04 to 46.02 lb in) for extruded holes.
Apply bearing type grease onto CE housing’s outer diameter where the o-ring is seated and apply a small amount of SAE20 oil into the bushing area.
Install the CE housing, brush-plate, and armature on the starter with the screws, assuring the same position as removed
Attach the three field leads to positive brushes with attaching screws for 12V, 24V & 32V models or two field leads to positive brushes with attaching screws for 64V models over the plug holes. Torque screws to 2.26 to 4.52 N m (20.00 to 40.00 lb in) for punched holes or 3.62 to 5.20 N.m (32.04 to 46.02 lb in) for extruded holes.
Install the three plugs to the frame and torque to 8.13 N.m (71.96 lb in).
Reinstall starter and connect cables and other leads, as removed.
Reconnect the negative (-) cable at the battery.