955522 Volvo.Penta Screw


955522 Screw Volvo.Penta AQD70D; TAMD70D; TAMD70E, D42A; D42A PP, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TD30A; TD31ACE; TD40A Screw
955522 Screw Volvo Penta
Rating:
63

Buy Screw 955522 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$56.65
 

29-08-2024
2.2[0.99] pounds
Amazon.com
Dorman 955-522 Driver Side Manual Door Mirror Compatible with Select Chevrolet Models, Black
Dorman Perfect replacement - reverse engineered to look, fit and function exactly like the original door mirror on your vehicle's specific year, make and model || Complete assembly - includes same mirror glass, housing, bracket and technology as the original part that came on the vehicle || Cost-effective and reliable - functions similarly to the original part but is much less expensive than getting a replacement from the dealership or original manufacturer || Easy installation - no special tools or equipment is necessary for installing this new part || Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool
Number on catalog scheme: 94
 

Volvo Penta entire parts catalog list:

AQD70D; TAMD70D; TAMD70E
D42A; D42A PP
MD70B; MD70BK; TMD70B; THAMD70B; TAMD70B; AQD70BL; AQD70B
MD70C; TMD70C; TAMD70C; THAMD70C; AQD70BL; AQD70CL
TD30A; TD31ACE; TD40A; TD45B; D45A

Information:


Illustration 1 g01436855
Schematic for the engine pressure sensors
Test Step 1. Inspect the Electrical Connectors and Wiring
Remove the electrical power from the ECM.
Illustration 2 g01199199
A typical left side view of the C9 engine
(1) Fuel pressure sensor
(2) Injection actuation pressure sensor
(3) Boost pressure sensor for the intake manifold
(4) Atmospheric pressure sensor
(5) Engine oil pressure sensor
(6) J2/P2 connectors
(7) ECM
(8) J1/P1 connectors
Illustration 3 g01255900
A typical left side view of the C7 engine
(9) Fuel pressure sensor
(10) Injection actuation pressure sensor
(11) Atmospheric pressure sensor
(12) Boost pressure sensor for the intake manifold
(13) Engine oil pressure sensor
(14) J2/P2 connectors
(15) ECM
(16) J1/P1 connectors
Thoroughly inspect connectors (6) and (8). Thoroughly inspect the connectors for each engine pressure sensor. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 4 g01209367
P2 ECM connector
(P2-15) Boost pressure sensor for the intake manifold
(P2-17) Sensor return
(P2-54) Sensor return
(P2-28) Engine oil pressure sensor
(P2-40) Fuel pressure sensor
(P2-57) Atmospheric pressure sensor
(P2-85) Injection actuation pressure sensor
(P2-72) +5 V Supply
(P2-80) +5 V Supply
Illustration 5 g01123211
Connectors for the sensors
(A) Supply
(B) Return
(C) Signal
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the engine pressure sensors.
Check the torque of the allen head screws for the ECM connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and wiring for abrasions and for pinch points from each sensor back to the ECM. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring and/or the connectors.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the problem is resolved.STOPTest Step 2. Check the Voltage on the +5 V Supply Wire
Remove the electrical power from the ECM.
Disconnect the harness connectors for the following sensors:
Injection actuation pressure sensor
Boost pressure sensor for the intake manifold
Atmospheric pressure sensor
Fuel pressure sensor
Engine oil pressure sensor
Restore the electrical power to the ECM.
Measure the voltage between terminals A (+5 VDC) and B (Return) at each sensor connector on the engine harness.
Remove the electrical power from the ECM.
Connect all of the sensors. Expected Result:Each voltage measurement is 5.0 0.2 VDC.Results:
OK - Each voltage measurement is 5.0 0.2 VDC. Proceed to Test Step 3.
Not OK - At least one voltage measurement is not 5.0 0.20 VDC.Repair: Refer to the diagnostic functional test Troubleshooting, "5 Volt Engine Pressure Sensor Supply Circuit - Test".STOPTest Step 3. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to electronic troubleshooting Troubleshooting, "Electronic Service Tools".
Restore the electrical power to the ECM.
Observe the "Active Diagnostic" screen on Cat ET. Wait at least 30 seconds so that any codes may become active. Look for an active diagnostic code for an engine pressure sensor.
Determine if the problem is related to a 03 diagnostic code or a 04 diagnostic code. Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active for the engine pressure sensors.Repair: If any of the above codes are logged and the engine is not running properly, refer to troubleshooting without a diagnostic code Troubleshooting.If the engine is running properly at this time, there may be an intermittent problem in a harness that is causing the codes to be logged. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOP
Active 04 code - An 04 diagnostic code is active. Proceed to Test Step 4.
Active 03 code - An 03 diagnostic code is active. Proceed to Test Step 5.Test Step 4. Disconnect the Suspect Sensor in Order to Create an Open Circuit
Remove the electrical power from the ECM.
Disconnect the sensor connector of the sensor with the 04 diagnostic code.
Restore the electrical power to the ECM. Wait at least 30 seconds for activation of the diagnostic codes.
Access the "Active Diagnostic Code" screen on Cat ET. Check for an active 03 diagnostic cod


Parts screw Volvo Penta:

417464
Screw
417464 Screw
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, T
21951336
 
21951336 Screw kit
AQD70D; TAMD70D; TAMD70E, D5A-T; D5A-TA; D5A-B TA, D5A-T; D5A-TA; D5A-B TA, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C
236872
Screw
236872 Screw
AQD70D; TAMD70D; TAMD70E, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TAMD60C, TMD100C, TMD121C; TAMD121C; TAMD121D
955772
 
955772 Screw
AQD70D; TAMD70D; TAMD70E, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70C; TMD70C; TAMD70C
956633
Screw
956633 Screw
AQD70D; TAMD70D; TAMD70E, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
130026
Screw
130026 Screw
D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B
847451
 
847451 Screw
D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TD100G-87; TD1030ME; TWD1030ME, TD70G; TD70G-83; TD70GPP
950052
 
950052 Screw
MD70B; MD70BK; TMD70B
Back to top