3858303 Volvo.Penta Seal


3858303 Seal Volvo.Penta SX-M; SX-MTD; SX-MTD3 Seal
3858303 Seal Volvo Penta
Rating:
43

Buy Seal 3858303 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$22.99

31-03-2025

CN: GlückMarine
GlückMarine 3863090 2 Pcs Oil Seals for OMC Cobra Vol-vo SX Stern Drives replace 3858303 3853474 3850482 GLM 86260
GluckMarine These 2 pcs shaft seals are compatible with OMC Cobra lower gearcase components 1994-1998 and Vol-vo SX out drives || Replace OMC 3863090, 3858303, 3853474, 3850482, 915223 0915223, Vol-vo Penta 3863090, 3858303 and GLM 86260 || Details: O.D. is 1.75", shaft size is 1.25" and width is 0.39" || The oil seals act as a physical barrier retaining the lubricating oil where it is bound to be and prevent the lubricating oil from leaking outside even under high pressure of the oil || The shift bracket seals also prevent dirt and other external entities from entering the system containing the lubricating oil
$25.90

31-03-2025

CN: AN-U Electric
Uanofcn 3863090 Lower Unit Gearcase Propeller Shaft Oil Seal O-ring 3852865 for OMC Stern Drive Engine Cobra SX Models Voolvo Penta SX Drives 306394 0333572
UANOFCN This is Uanofcn Shift Shaft Lower Unit Gearcase Oil Seal for OMC Stern Drive || Fit OMC Stern Drive Engine Cobra SX Models (1994 & Up) Voolvo Penta SX Drives || Replaces Prop Shaft Carrier O-ring seal 3863090, O-ring seal 3852865 || Replaces Propeller Nut Cotter Pin 3063940019084 Drain Fill Washer Gasket 0333572 || Package Includes: Oil seal * 1, O-ring seal * 1, Gasket * 1, Cotter Pin*1
$58.73
 

25-06-2024

US: AUTO COMMITTEE
Shaft Bearing Housing Oil Seal fits - 3863090 3858303, RCR 3863090 1994-1998 Cobra 3853474, 3858303, 3863090/3853474
AUTO COMMITTEE Fix that squeaky brake, knocking engine, or clicking starter with Auto-Committee replacement parts to save money down the road. || Compatible: : RCR 3863090 1994-1998 Cobra 3853474, 3858303, 3863090 / 3853474 || Aftermarket Parts. NOT an OEM. || High-Tech materials provides unmatched reliability and performance. Direct replacement to your original unit. || If there are any questions as to this product, please contact us directly for technical support. Please verify your requirements or contact us before ordering.
Number on catalog scheme: 9
 

Compatible models:

Volvo Penta entire parts catalog list:

SX-M; SX-MTD; SX-MTD3; SX-M 1.43; SX-M 1.51; SX-M 1.60; SX-M 1.66; SX-M 1.79; SX-M 1.89; SX-M 1.97; SX-M 2.18; SX-MTD 1.66; SX-MTD 1.79; SX-M

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Ensure that the engine lubricating oil is drained. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.Note: In order to remove a cast iron oil pan, the engine must be removed from the machine. The engine should be mounted in a suitable stand and placed in the inverted position.
Illustration 1 g02835137
Mount the engine in a suitable stand and place in the inverted position.
If necessary, remove dipstick (2) from engine oil pan (3).
Remove sealing washer (5) (not shown) from oil drain plug (6).
Remove bolts (4) from engine oil pan (3). Note: Support the weight of the engine oil pan.
Remove the engine oil pan from the cylinder block.
Remove gasket (1) (not shown).
Illustration 2 g02835177
Typical example
If necessary, follow Step 7.a through Step 7.d in order to remove oil suction pipe (8) from the cylinder block.
Remove Allen head cap screw (9) from oil suction pipe (8).
Remove bolts (10) from the oil suction pipe.
Remove the oil suction pipe from the cylinder block.
Remove O-ring (7) from oil suction pipe (8). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 3 g02835177
Typical example
If necessary, follow Step 2.a through Step 2.f in order to install oil suction pipe (8).
Install new O-ring seal (7) to oil suction pipe (8).
Install the oil suction pipe to the cylinder block.
Install the Allen head cap screw to the oil suction pipe.
Install bolts (10) to the oil suction pipe support.
Tighten Allen head cap screw (9) to a torque of 10 N m (89 lb in).
When M8 bolts are installed, tighten bolts (10) to a torque of 25 N m (221 lb in). When M10 bolts are installed, tighten bolts (10) to a torque of 45 N m (33 lb ft).
Clean the mating surface of the cylinder block.
Illustration 4 g02835137
Illustration 5 g02835539
Initial tightening sequence
Illustration 6 g02835357
Secondary tightening sequence
Position gasket (1) (not shown) onto engine oil pan (4).
Position spacer (2) onto the engine oil pan.
Position the engine oil pan onto the cylinder block. Use a suitable tool to support the weight of the engine oil pan.
Install bolts (4) finger tight. Note: Ensure that the rear of the engine oil pan is aligned with the rear of the cylinder block.
Tighten bolts (4) in the initial sequence that is shown in Illustration 5. Tighten bolts (7) to a torque of 45 N m (33 lb ft).
Tighten bolts (4) in the final sequence that is shown in Illustration 6. Tighten bolts (7) to a torque of 45 N m (33 lb ft).
Install a new sealing washer (5) to oil drain plug (6).
Install oil drain plug (6) to the engine oil pan . Tighten the oil drain plug to a torque of 50 N m (37 lb ft).
Remove the engine from the suitable stand.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.


Parts seal Volvo Penta:

3852560
Seal
3852560 Seal
DP-SM; DP-SM 1.68; DP-SM 1.78, SX-C; SX-C1; SX-C2, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3, SX-S; SX-SLT; SX-ST, TSKs; SX-M; 1998-2005, TSKs; SX-M; 2006-2008
3852272
Seal
3852272 Seal
DP-SM; DP-SM 1.68; DP-SM 1.78, SX-A; DPS-A; DPS-B, SX-C; SX-C1; SX-C2, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3, SX-S; SX-SLT; SX-ST, XDP-B; TSK X-B; TSK X-BLT
3852315
 
3852315 Seal
DP-SM; DP-SM 1.68; DP-SM 1.78, SX-C; SX-C1; SX-C2, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3, SX-S; SX-SLT; SX-ST
3854595
 
3854595 Seal
DP-SM; DP-SM 1.68; DP-SM 1.78, SX-C; SX-C1; SX-C2, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3
3863090
Seal
3863090 Seal
SX-A; DPS-A; DPS-B, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3
Back to top