1543572 Sealing ring Volvo.Penta
TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TAMD63L-A; TAMD63P-A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD74A; TAMD74A-A; TAMD74A-B, TD164KAE, TID162AG
Sealing
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Connection Pipe Seal for Volvo Truck D16 Engine 1543572
TKB High Quality || 100% Guaranteed || Fit: Volvo Truck D16 Engine || New
TKB High Quality || 100% Guaranteed || Fit: Volvo Truck D16 Engine || New
Compatible models:
TAD1630P; TWD1630P; TWD1630PP
TAD1630V; TWD1630V
TAMD162A; TAMD162B; TAMD162C
TAMD162C-C; TAMD163A-A; TAMD163P-A
TAMD165A; TAMD165C; TAMD165P
TAMD63L-A; TAMD63P-A
TAMD71B; TAMD73P-A; TAMD73WJ-A
TAMD74A; TAMD74A-A; TAMD74A-B
TD164KAE
TID162AG; TID162AGP; TID162AP
TWD1620G; TWD1630G; TAD1630G
Volvo.Penta
Volvo Penta entire parts catalog list:
- Collecting Pipe » 1543572
- Collecting Pipe
- Oil Cooler
- Water Pump and Thermostat
- Water Pump and Thermostat
- Water Pump and Thermostat
- Water Pump and Thermostat
- Repair Kits
- Repair Kits
- Oil Cooler
- Water Pump and Thermostat
- Water Pump and Thermostat
- Water Pump and Thermostat
- Water Pump and Thermostat
- Repair Kits
- Repair Kits
- Water Pump, Water Filter and Thermostat
- Collecting Pipe
- Collecting Pipe
- After Cooler and Installation Components: SN-XXXXXXXXXX/19705
- After Cooler and Installation Components: SNXXXXXXXXXX/19706-
- Repair Kits: A
- Repair Kits: B
- Repair Kits: C
- Collecting Pipe: A
- Collecting Pipe: B
- Collecting Pipe: B
- Collecting Pipe: C
- Collecting Pipe: C
- Water Pump, Water Filter and Thermostat: A
- Water Pump, Water Filter and Thermostat: B
- Water Pump, Water Filter and Thermostat
- Repair Kits
- Repair Kits
- Repair Kits
- Collecting Pipe: A
- Collecting Pipe: B
- Collecting Pipe: B
- Collecting Pipe: C
- Collecting Pipe: C
- Water Pump, Water Filter and Thermostat: A
- Water Pump, Water Filter and Thermostat: B
- Water Pump, Water Filter and Thermostat
- Repair Kits: A
- Repair Kits: B
- Repair Kits: C
TAMD71B; TAMD73P-A; TAMD73WJ-A
TAMD74A; TAMD74A-A; TAMD74A-B; TAMD74C-A; TAMD74C-B; TAMD74L-A; TAMD74L-B; TAMD74P-A; TAMD74P-B; TAMD75P-A
TD164KAE
TID162AG; TID162AGP; TID162AP; TID162APB
- Water Pump and Thermostat Housing, SNXXXXXXXXXX/6061-
- Collecting Pipe: EARLIER PRODUCTION
- Collecting Pipe: LATER PRODUCTION
- Collecting Pipe: LATER PRODUCTION
- Oil Cooler
- Repair Kits
- Oil Cooler
- Water Pump and Thermostat
- Water Pump and Thermostat
- Water Pump and Thermostat
- Collecting Pipe: EARLIER PRODUCTION
- Collecting Pipe: LATER PRODUCTION
- Collecting Pipe: LATER PRODUCTION
- Collecting Pipe: TIDIGARE UTFÖRANDE
- Collecting Pipe: SENARE UTFÖRANDE
- Collecting Pipe: SENARE UTFÖRANDE
- Repair Kits
- Repair Kits
- Repair Kits
- Repair Kits
Information:
start by: a) remove timing gear cover and oil pump1. Remove the plug from the fuel injection pump housing and install timing pin (A).2. While turning the crankshaft clockwise as seen from the front of the engine, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft.3. Remove the tachometer drive adapter shaft and install tooling (B) as follows: a) Install bolt assembly (2) in the fuel injection pump camshaft. The bolt assembly must turn freely into the camshaft. Do not use force to install the bolt assembly.b) Install bolt (1) in the gear.c) Tighten the bolt and remove gear (3). 4. Remove screw (4), washer (5), and gear (6) from the camshaft. 5. Install tooling (C) and remove gear (7) from the camshaft.Install Camshaft Gears (Engines With Taper Drive For Fuel Injection Pump)
Do not heat the gear for the camshaft with a torch or to a temperature of more than 400°F (204°C). Higher temperatures can cause the dowels to loosen and come out of the gear. Do not use force to install the gear. Damage to the camshaft or camshaft thrust pin can be the result.
1. Heat the large gear for the camshaft to a maximum temperature of 400°F (204 C). Put the groove (slot) on the gear in alignment with the dowel on the camshaft and install the gear so the timing marks on the camshaft gear and crankshaft gear are in alignment.
GEARS SHOWN OUT OF ENGINE FOR BETTER PHOTO ILLUSTRATION2. Put gear (1) in position on the dowels. Put pin (4) on washer (3) in alignment with hole (2) and install the washer.
GEARS SHOWN OUT OF ENGINE BETTER PHOTO ILLUSTRATION3. Install screw (5). Tighten the screw to a torque of 108 36 lb.in. (124.5 41.5 cm.kg). Put marks (stake) on the screw in two places with a hammer and punch. 4. Put gear (7) for the fuel injection pump camshaft in position and install tachometer drive adapter shaft (6). Tighten the shaft to a torque of 32 2 lb.ft. (4.4 0.3 mkg).5. After the timing gear cover has been installed, check the timing as follows: a) Remove timing pin (A).b) Turn the crankshaft clockwise as seen from the front of the engine approximately 1/2 turn. Install timing pin (A) again.c) While turning the crankshaft clockwise, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft. d) Remove plug (8) from the timing hole. Remove bolt (9) and install it through the timing hole and into the camshaft gear. The timing is correct when timing pin (A) is installed in the fuel injection pump camshaft and bolt (9) is installed in the camshaft gear.e) Remove the bolt and install the plug. Remove timing pin (A) and install the plug. If the bolt can not be installed, the timing must be corrected as follows: a) With timing pin (A) installed, remove the tachometer drive adapter housing and shaft.b) Loosen the gear from the fuel injection pump camshaft. Turn the crankshaft clockwise approximately two full turns until bolt (9) can be installed. Install the bolt.c) Install tachometer drive adapter shaft and tighten it to a torque of 32 2 lb.ft. (4.4 0.3 mkg). Install the adapter housing. Remove the bolt and timing pin and install the plugs.end by: a) install timing gear cover and oil pump
Do not heat the gear for the camshaft with a torch or to a temperature of more than 400°F (204°C). Higher temperatures can cause the dowels to loosen and come out of the gear. Do not use force to install the gear. Damage to the camshaft or camshaft thrust pin can be the result.
1. Heat the large gear for the camshaft to a maximum temperature of 400°F (204 C). Put the groove (slot) on the gear in alignment with the dowel on the camshaft and install the gear so the timing marks on the camshaft gear and crankshaft gear are in alignment.
GEARS SHOWN OUT OF ENGINE FOR BETTER PHOTO ILLUSTRATION2. Put gear (1) in position on the dowels. Put pin (4) on washer (3) in alignment with hole (2) and install the washer.
GEARS SHOWN OUT OF ENGINE BETTER PHOTO ILLUSTRATION3. Install screw (5). Tighten the screw to a torque of 108 36 lb.in. (124.5 41.5 cm.kg). Put marks (stake) on the screw in two places with a hammer and punch. 4. Put gear (7) for the fuel injection pump camshaft in position and install tachometer drive adapter shaft (6). Tighten the shaft to a torque of 32 2 lb.ft. (4.4 0.3 mkg).5. After the timing gear cover has been installed, check the timing as follows: a) Remove timing pin (A).b) Turn the crankshaft clockwise as seen from the front of the engine approximately 1/2 turn. Install timing pin (A) again.c) While turning the crankshaft clockwise, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft. d) Remove plug (8) from the timing hole. Remove bolt (9) and install it through the timing hole and into the camshaft gear. The timing is correct when timing pin (A) is installed in the fuel injection pump camshaft and bolt (9) is installed in the camshaft gear.e) Remove the bolt and install the plug. Remove timing pin (A) and install the plug. If the bolt can not be installed, the timing must be corrected as follows: a) With timing pin (A) installed, remove the tachometer drive adapter housing and shaft.b) Loosen the gear from the fuel injection pump camshaft. Turn the crankshaft clockwise approximately two full turns until bolt (9) can be installed. Install the bolt.c) Install tachometer drive adapter shaft and tighten it to a torque of 32 2 lb.ft. (4.4 0.3 mkg). Install the adapter housing. Remove the bolt and timing pin and install the plugs.end by: a) install timing gear cover and oil pump
Parts sealing Volvo Penta:
842913
842913 Sealing ring
430; 430A; 430B, 500; 500A; 501A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C, BB231A; BB2
1545283
1545283 Sealing ring
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD41D; D41D; TAMD41D, AQD70D; TAMD70D; TAMD70E, D100BHC; D100BRC; TD100AHC, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, MD100A; TMD100A
1676432
1676432 Sealing ring
AD31L-A; AD31P-A; AD41L-A, DH10A; DH10A 285; DH10A 360, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42P-A; KAMD42P-A; HS1A, TAD1030G; TD1010G; TWD1010G, TAD1230G; TD1210G; TWD1210G, TAD1630P; TWD1630P; TWD1630PP, TAD1640GE; TAD1641GE; TAD1642GE, TAMD103A, TAMD1
943342
943342 Sealing ring
D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D12D-A MH; D12D-B MH; D12D-C MH, D13B-E MH; D13B-E MH (FE); D13B-N MH, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, D3-110I-A; D3-110I-B; D3-110I-C, D4-180I-B; D4-180I-C; D4-180I-
1544710
1544710 Sealing ring
D12D-A MH; D12D-B MH; D12D-C MH, D4-180I-B; D4-180I-C; D4-180I-D, D4-180I-F; D4-225A-F; D4-225I-F, D6-280A-A; D6-280A-B; D6-280A-C, D6-300A-F; D6-300D-F; D6-300I-F, DH10A; DH10A 285; DH10A 360, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD10
864647
864647 Sealing ring
D8A1-A MP; D8A2-A MP, TAMD61A; TAMD62A, TAMD63L-A; TAMD63P-A, TAMD71A; TAMD72A, TAMD71B; TAMD73P-A; TAMD73WJ-A
3825543
3825543 Sealing ring
TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1230P; TD121GP-87; TWD1210P, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A
862419
862419 Sealing ring
TAMD162A; TAMD162B; TAMD162C, TD120HP-86; TD121; TD121G, TWD1620G; TWD1630G; TAD1630G