1543573 Sealing ring Volvo.Penta
TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD162A; TAMD162B; TAMD162C, TID162AG; TID162AGP; TID162AP, TWD1620G; TWD1630G; TAD1630G
Sealing
Price: query
Rating:
Compatible models:
Volvo Penta entire parts catalog list:
- Repair Kits » 1543573
- Repair Kits
TAMD162A; TAMD162B; TAMD162C; TAMD162C-B
TID162AG; TID162AGP; TID162AP; TID162APB
- Water Pump and Thermostat Housing, SN-XXXXXXXXXX/6060
- Water Pump and Thermostat Housing, SNXXXXXXXXXX/6061-
Information:
Typical Example
Typical Example1. Remove the covers and gaskets over camshaft gears (3).2. Remove cover (1) from the top of the flywheel housing.3. Remove bolts (2) and the plate and adapter that fasten the camshaft gears to the camshaft.4. Put the three washers from tooling (A) behind plate (5) and install the bolt and plate (5).
Do not apply more than 51675 kPa (7500 psi) pressure to 1P820 Hydraulic Puller. 8B7559 adapters are rated at 6 1/2 ton each and 1P820 Hydraulic Puller is rated at 17 ton at 68900 kPa (10000 psi). If to much pressure is applied, the gear can be damaged.
5. Install tooling (A) on camshaft drive gear (3). Apply 51,675 kPa (7500 psi) to the puller and hit the screw part of the puller with a hammer until the gear is free of the camshaft taper. Remove tooling (A) and gears (3).6. Put stands or blocks under the rear of the engine block. The weight of the engine is approximately 6090 Kg (13,400 lb.).7. Install tooling (B) on the top of the flywheel housing and attach a hoist.8. Remove all bolts that fasten the flywheel housing to the engine block. Be aware that there are two bolts below cover (1), and the two bolts that pass through shaft (4) must also be removed.9. Remove the flywheel housing from the engine. The weight of the flywheel housing is 210 Kg (454 lb.).Install Flywheel Housing
1. Use 6V1541 Quick Cure primer to clean the mating surfaces of the flywheel housing and the cylinder block. Put 6V6640 Gasket Maker on the surfaces of the flywheel housing that make contact with the cylinder block.2. Install tooling (A) on the top of the flywheel housing. Fasten a hoist and put the flywheel housing in position on the cylinder block. 3. Install the bolts in their respective locations. See the Installation Chart. Tighten the 1/2" - NC bolts to a torque of 135 15 N m (100 11 lb. ft.). Tighten the 5/8" NC bolts to a torque of 270 25 N m (200 18 lb.ft.).
Typical Example
Typical Example4. Put the camshaft timing pins in position and put the timing bolt in the flywheel with Number 1 piston at the compression stroke. See the topic, Install Camshafts in this module. Be sure gear backlash is removed.5. Install camshaft gears (2), tach drive adapter (4), plate (1) and bolts (3). Tighten bolts (3) as follows: a. Tighten bolts (3) to a torque of 360 50 N m (265 35 lb.ft.).b. Hit bolts (3) with a soft hammer to seat the gear on the camshaft.c. Tighten bolts (3) again to a torque of 360 50 N m (265 35 lb.ft.).d. Repeat Steps b and c until the torque does not change.6. Remove the timing pins from the camshafts and the flywheel.7. Install the cover on the top of the flywheel housing and the covers over both camshaft drive gears. Two bolts, that fasten each camshaft gear cover to the flywheel housing, are longer and must be installed at locations (X).End By: a. install crankshaft rear seal and wear sleeveb. install oil pan, (rear half only)c. install electric starting motorsd. install enginee. install tach drive
Parts sealing Volvo Penta:
1543572
1543572 Sealing ring
TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TAMD63L-A; TAMD63P-A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD74A; TAMD74A-A; TAMD74A-B, TD164KAE, TID162AG
1545283
1545283 Sealing ring
AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD41D; D41D; TAMD41D, AQD70D; TAMD70D; TAMD70E, D100BHC; D100BRC; TD100AHC, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, MD100A; TMD100A
1676432
1676432 Sealing ring
AD31L-A; AD31P-A; AD41L-A, DH10A; DH10A 285; DH10A 360, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42P-A; KAMD42P-A; HS1A, TAD1030G; TD1010G; TWD1010G, TAD1230G; TD1210G; TWD1210G, TAD1630P; TWD1630P; TWD1630PP, TAD1640GE; TAD1641GE; TAD1642GE, TAMD103A, TAMD1
1543225
1543225 Sealing ring, oil pump
D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAD940GE; TAD941GE, TAD940VE; TAD941VE; TAD942VE, TAMD162A; T
1544710
1544710 Sealing ring
D12D-A MH; D12D-B MH; D12D-C MH, D4-180I-B; D4-180I-C; D4-180I-D, D4-180I-F; D4-225A-F; D4-225I-F, D6-280A-A; D6-280A-B; D6-280A-C, D6-300A-F; D6-300D-F; D6-300I-F, DH10A; DH10A 285; DH10A 360, TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD10
276924
276924 Sealing ring kit, cylinder head
TAD1630V; TWD1630V, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TD164KAE, TID162AG; TID162AGP; TID162AP, TWD1620G; TWD1630G; TAD1630G
7745600_000
863779
863779 Sealing ring
TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P