864241 Volvo.Penta Sealing ring

Illustration 1 g00807537
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector, the J61/P61 machine connector, and the J403/P403 throttle position sensor connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Inspect the Throttle Pedal Assembly
Inspect the throttle pedal assembly for components that are loose, bent, missing, or worn.
Slowly depress the pedal and release the pedal.Expected Result:The throttle pedal assembly should operate smoothly without excessive drag. The pedal should return to the low idle position without assistance in less than one second.Results:
OK - The throttle pedal assembly functions properly. Proceed to Test Step 3.
Not OK - Repair: Repair the throttle pedal assembly, as required.STOPTest Step 3. Check the Status on ET
Connect ET to the service tool connector.
Turn the keyswitch to the ON position.
Observe the status of "Throttle Position" on ET while you operate the throttle pedal.Expected Result:The status should be approximately 0 percent when the throttle pedal is released. The status should progressively increase to 100 percent when the throttle pedal is fully depressed.Results:
OK - The throttle position sensor is working properly.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - Proceed to Test Step 4.Test Step 4. Check the Supply Voltage at the Sensor
Install a 7X-6370 Adapter Cable (3 Pin DT Breakout) at the J403/P403 throttle position sensor connector.
Turn the keyswitch to the ON position.
Measure the voltage across terminal A (Digital Sensor +8 VDC) and terminal B (Digital Return) at the breakout.Expected Result:The supply voltage should be 8.0 0.5 VDC.Results:
OK - The sensor is receiving the correct supply voltage. Proceed to Test Step 5.
Not OK - The correct supply voltage is not reaching the sensor.Repair: Proceed to Troubleshooting, "Digital Sensor Supply Circuit - Test".STOPTest Step 5. Check the Isolated Signal Frequency and the Duty Cycle at the Sensor
Remove the wire from the harness side of P403:C (Signal).
Turn the keyswitch to the ON position.
Measure the frequency and the duty cycle between terminal B (Digital Return) and terminal C (Signal) at the J403/P403 breakout while you operate the throttle pedal.
Turn the keyswitch to the OFF/RESET position.
Reinstall the wire in P403:C (Signal).Expected Result:The frequency should be between 150 and 1000 Hz. The duty cycle should be between 10 and 35 percent when the pedal is released. The duty cycle should be between 60 and 90 percent when the pedal is fully depressed.Results:
OK - The sensor is producing a valid signal. Proceed to Test Step 6.
Not OK - The sensor is not producing a valid signal.Repair: Replace the throttle position sensor.Verify that the repair eliminates the problem.STOPTest Step 6. Check for a Short Circuit in the Wiring Harness
Disconnect the J1/P1 ECM connector and the J403/P403 throttle position sensor connector.
Measure the following resistances:
P403:A (Digital Sensor +8 VDC) and P403:B (Digital Return)
P403:A (Digital Sensor +8 VDC) and P403:C (Throttle Position)
P403:B (Digital Return) and P403:C (Throttle Position)Expected Result:The resistance should be greater than 20,000 Ohms for each measurement.Results:
OK - There are no shorts in the harness. Proceed to Test Step 7.
Not OK - There is a short circuit in the harness or connectors.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 7. Check the Resistance through the Harness
Illustration 2 g00807533
ECM connector P1
Fabricate a jumper wire with pins at both ends.
Use the jumper wire to short P403:A (Digital Sensor +8 VDC) and P403:C (Throttle Position) together.
Measure the resistance between P1:66 (Throttle Position) and P1:4 (Digital Sensor +8 VDC).
Move the one end of the jumper wire from P403:A (Digital Sensor +8 VDC) to P403:B (Digital Return). Leave the other end in P403:C (Throttle Position).
Measure the resistance between P1:66 (Throttle Position) and P1:5 (Digital Sensor Return).
Remove the jumper wire and reconnect all of the connectors.Expected Result:The resistance should be less than 10 Ohms for each measurement.Results:
OK - The harness is good. Proceed to Test Step 8.
Not OK - There is an open circuit or excessive resistance in the harness or the connectors.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 8. Check the Signal Frequency and the Duty Cycle at the ECM
Illustration 3 g00807533
Remove the signal wire from J2:66 (Throttle Position).
Turn the keyswitch to the ON position.
Measure the frequency and the duty cycle between the signal wire and the ECM ground strap while you operate the throttle pedal.
Turn the keyswitch to the OFF/RESET position.
Reinstall the signal wire in J2:66.Expected Result:The frequency should be between 150 and 1000 Hz. The duty cycle should be between 0 and 35 percent when the pedal is released. The duty cycle should be between 55 and 100 percent when the pedal is fully depressed.Results:
OK - A valid sensor signal is reaching the ECM. Proceed to Test Step 9.
Not OK - There is an intermittent problem in the wiring harness or the connectors.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 9. Check the Status on ET
Turn the keyswitch to the ON position.
Observe the status for "Throttle Position" on ET while you operate the throttle pedal.Expected Result:The status should read approximately 0 percent when the throttle pedal is released. The status should progressively increase to 100 percent when the throttle pedal is fully depressed.Results:
OK - The throttle position sensor is working properly.Rep