382177 Volvo.Penta Selector fork


382177 Selector fork Volvo.Penta D100A; D100AK; D100B, D120A; D120AK; TD120A Selector
382177 Selector fork Volvo Penta
Rating:
93

Buy Selector fork 382177 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$448.37
 

01-09-2017
22.00[9.90] pounds
American S: American Shifter
American Shifter 382177 Shifter Kit (PG 23" Trim Kit Dipstick For D19AD, 1 Pack)
Application: Powerglide||Shifter Style: Push Button & Side Detent||Shifter Arm Size: 23in Single Bend||Shifter Arm Finish: Chrome||Knob: Standard
Number on catalog scheme: 3
 

Compatible models:

Volvo Penta entire parts catalog list:

D100A; D100AK; D100B; TD100A; TD100AG; TD100AK
D120A; D120AK; TD120A; TD120AG; TD120AG PP; TD120AK

Information:

Engine Specifications
Note: The front end of the engine is opposite the flywheel end of the engine. The left and the right sides of the engine are determined from the flywheel end. The number 1 cylinder is the front cylinder.
Illustration 1 g01387009
Cylinder and valve location
(A) Exhaust valve
(B) Inlet valve
Table 1
C15 Engine Specifications
Arrangement and Cylinders In-line six cylinder
Bore 137 mm (5.4 inch)
Stroke 171 mm (6.7 inch)
Aspiration ATAAC(1)
Displacement 15.2 L (928 cubic inch)
Firing Order 1-5-3-6-2-4
Rotation (flywheel end) Counterclockwise
(1) Air-to-air aftercooled
Table 2
C18 Engine Specifications
Arrangement and Cylinders In-Line six cylinder
Bore 145 mm (5.7 inch)
Stroke 183 mm (7.2 inch)
Aspiration ATAAC(1)
Displacement 18.1 L (1105 cubic inch)
Firing Order 1-5-3-6-2-4
Rotation (flywheel end) Counterclockwise
(1) Air-to-air aftercooledElectronic Engine Features
The Caterpillar C15 and C18 Engine are designed for electronic controls. The integral on board computer controls the operation of the engine. Current operating conditions are monitored. The Electronic Control Module (ECM) controls the response of the engine to these conditions and to the demands of the operator. These conditions and operator demands determine the precise control of fuel injection by the ECM. The electronic engine control system provides the following features:
Engine speed governor
Automatic air/fuel ratio control
Torque rise shaping
Injection timing control
System diagnostics
Aftertreatment regeneration control
NOx reduction system controlAdditional Features
The following additional features provide increased engine fuel economy and serviceability:
Cold starting capability
Tampering detection
DiagnosticsEngine Diagnostics
The engine has built-in diagnostics in order to ensure that all of the components are functioning properly. Under certain conditions, the engine horsepower and the vehicle speed may be limited. A Caterpillar electronic service tool may be used to display the diagnostic code.There are two categories of codes: diagnostic code and event code. These two categories of codes may be in two different states: active and logged.Most of the diagnostic codes are logged and stored in the ECM. For additional information, refer to the Operation and Maintenance Manual, "Engine Diagnostics" topic (Operation Section).Engine Service Life
Engine efficiency and maximum utilization of engine performance depend on the adherence to proper operation and maintenance recommendations. In addition, use recommended fuels, coolants, and lubricants. Use the Operation and Maintenance Manual as a guide for required engine maintenance.Expected engine life is predicted by the average power that is demanded. The average power that is demanded is based on fuel consumption of the engine over a time. Reduced hours of operation at full throttle and/or operating at reduced throttle settings result in a lower average power demand. Reduced hours of operation will increase the length of operating time before an engine overhaul is required. For more information, refer to the Operation and Maintenance Manual, "Overhaul Considerations" topic (Maintenance Section).Aftermarket Products and Caterpillar Engines
In order to maximize fuel system life and prevent premature wear out from abrasive particles in the fuel, a four micron[c] absolute high efficiency fuel filter is required for all Caterpillar common rail fuel systems. Caterpillar High Efficiency Fuel Filters meet these requirements. Consult your Caterpillar dealer for the proper part numbers.
When auxiliary devices, accessories, or consumables (filters, additives, catalysts, etc.) which are made by other manufacturers are used on Caterpillar products, the Caterpillar warranty is not affected simply because of such use.However, failures that result from the installation or use of devices, accessories, or consumables from other manufacturers are NOT Caterpillar defects. Therefore, the defects are NOT covered under the Caterpillar warranty.


Parts selector Volvo Penta:

382176
Selector shaft, 1ST
382176 Selector shaft, 1ST
D100A; D100AK; D100B, D120A; D120AK; TD120A
382174
Selector shaft, 3RD
382174 Selector shaft, 3RD
D100A; D100AK; D100B, D120A; D120AK; TD120A
382175
Selector fork
382175 Selector fork
D100A; D100AK; D100B, D120A; D120AK; TD120A
382506
Selector shaft, reverse
382506 Selector shaft, reverse
D100A; D100AK; D100B, D120A; D120AK; TD120A
382182
Selector fork
382182 Selector fork
D100A; D100AK; D100B, D120A; D120AK; TD120A
1523080
 
1523080 Selector fork
D120A; D120AK; TD120A, RAN181; RAN280; RAN480, TD120C
384135
Selector shaft
384135 Selector shaft
D120A; D120AK; TD120A, RAN181; RAN280; RAN480, TD120C
Back to top