424864 Volvo.Penta Shaft


424864 Shaft Volvo.Penta DH10A; DH10A 285; DH10A 360 Shaft
424864 Shaft Volvo Penta
Rating:
48

Buy Shaft 424864 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$25.40
 

24-04-2023
1.8[0.81] Pounds
-: -
Tork Xpress Mini Multifold Hand Towel Dispenser - Wall Mount Tissue Dispenser with Smart Lock - Suitable for Tork H2 Premium Paper Towels, Color: White
Improve your restroom design with a sleek commercial mini folded paper towel dispenser with one-at-a-time dispensing. || Create an accessible restroom with this paper towel dispenser—it protrudes less than 4.0" to comply with ADA requirements. || Improve your restroom design with this dispenser, winner of the iF Design Award and Red Dot Award 2009. || Make maintenance and refills easy—the window lets you see when refills are due and side loading makes it easy to stock. || Design: Elevation. W 11.9" H 11.5" D 4.0" Material: Plastic. Color: White. Suitable for H2 refills from Tork.
$99.95
 

17-04-2020

-: -
Tork 552120 Elevation Xpress Mini Hand Towel Dispenser, 11.6" Height x 11.9" Width x 4.0" Depth, White (Case of 1 Dispenser) for use with Tork 100297, 420570, 101293, 424814 and 424864 (2 Pack)
The Tork Xpress Multifold Mini Hand Towel Dispenser in Elevation Design is suitable for environments that demand both comfort and hygiene This slim, attractive dispenser fits in low to medium traffic washrooms where space is limited One at a time dispensing reduces cost-in-use and waste - Hygienic as users only touch the towel they will use Paper towel bundles can be topped up easily to avoid paper run-outs For use with Tork 100297, 100293, 420570, 424814 and 424864 multifold paper towels

Compatible models:

Volvo Penta entire parts catalog list:

DH10A; DH10A 285; DH10A 360; DH10A Rail; THD102KD; THD102KB

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Mechanical Electronic Injector Unit (MEIU) and Valve Lash Adjustment
Put the number 1 piston at Top Dead Center (TDC) on the compression stroke. Refer to the Testing and Adjusting, Finding Top Center Position No. 1 Piston.Note: To check that the number 1 piston is on TDC, both the inlet and exhaust valves on cylinder number 1 will move freely. If the valves do not move freely, cylinder number 1 is on TDC of the exhaust stroke. Install the timing pin in the flywheel.
Table 1
TDC No. 1 Compression Stroke Inlet Valves Exhaust Valves
Valve Lash C13
0.38 0.08 mm (0.015 0.003 inch) C13
0.76 0.08 mm (0.030 0.003 inch)
Cylinders 1–2–4 1–3–5
Adjust the valve lash using the specifications from Table 1.
Lightly tap the rocker arm with a soft mallet.Note: This tapping ensures that the roller lifter seats against the base circle of the camshaft.
Loosen the adjustment locknut for the appropriate valves.
Place the feeler gauge between the rocker arm and the valve bridge.
Turn the adjustment screw in a clockwise direction while sliding the feeler gauge back and forth between the rocker arm and valve bridge. Continue turning the adjustment screw in a clockwise direction until a slight drag is felt on the feeler gauge.
Tighten the


Parts shaft Volvo Penta:

70307303
 
70307303 Shaft coupling
DH10A; DH10A 285; DH10A 360
469886
Shaft
469886 Shaft
DH10A; DH10A 285; DH10A 360
Back to top