865245 Shaft Volvo.Penta
TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P
Shaft
Price: query
Rating:
Compatible models:
Volvo Penta entire parts catalog list:
TAMD162C-C; TAMD163A-A; TAMD163P-A
TAMD165A; TAMD165C; TAMD165P; TAMD165A-A; TAMD165C-A; TAMD165P-A
Information:
Start By:a. remove fuel injection pumpsb. disassemble governorc. remove fuel transfer pump 1. Loosen screws (1) in the levers, and remove screw (3) in the crossover lever. Slide shaft assembly (2) out of the housing. 2. Loosen the screws in levers (4), and remove the screw in crossover lever (5). Slide shaft (6) out of the housing. Put identification marks on lifters (7) and rollers (8) for installation in their respective bores in the housing.3. Use a magnet to remove eight lifter assemblies (7). 4. Remove roller (8) from each lifter assembly. 5. Turn the camshaft so the groove (slot) for the timing pin is in the position shown, and carefully remove camshaft (9). Remove the thrust washer from the housing. 6. Remove camshaft rear bearing (10) from the fuel pump housing. Be careful not to damage the bearing bore in the housing. 7. Use Tool (A) to remove the camshaft front bearing from the fuel pump housing.Assemble Fuel Injection Pump Housing
Put clean fuel on all parts during assembly.1. Use Tooling (A) to install the camshaft front bearing in the housing. Install the bearing with the chamfer toward the inside of the pump housing.2. Install the bearing so it is even with the front face of the pump housing. 3. Use Tooling (B) to machine the bore in the camshaft front bearing to the correct size. See Special Instruction, SMHS6735 for the procedure to machine the new camshaft front bearing. The bore in the bearing must be 25.413 0.013 mm (1.0005 .0005 in). 4. Use Tooling (A) to install the camshaft rear bearing in the housing. Install the bearing so groove (1) in the bearing is in the position shown. On earlier pump housings without a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.114 0.025 mm (.0045 .0010 in)below face (X) on the housing. On later pump housings with a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.43 0.13 mm (.017 .005 in)below the counterbore for the thrust washer. 5. Install thrust washer (2) in the housing with the ear on the thrust washer in the hole in the pump housing so the thrust washer will not turn.6. With the pump housing in a vertical position as shown, carefully install camshaft (3). To make sure that the thrust washer will be kept in its correct installation location, keep the pump housing in a vertical position, and install the fuel transfer pump and camshaft sleeve. See Fuel Transfer Pump Installation for the procedure to install the fuel transfer pump and camshaft sleeve.
If the pump housing is assembled while it is in a horizontal position, the thrust washer can slide out of the counterbore and into the area between the camshaft thrust face and the housing. Then the fuel pump camshaft end play will not be correct, and it will be necessary to disassemble the fuel pump housing so the thrust washer can be installed correctly.
7. Install each roller (4) in their respective lifters. 8. Use a magnet to install lifter assemblies (5) in their respective bores in the pump housing with the groove in each lifter in alignment with the dowel in the lifter bore. 9. Install shaft (6) in the pump housing; then through one lever (7); then through crossover lever (8); then through three levers (7) as shown. Install the screw in crossover lever (8). Tighten the screw in crossover lever (8). Tighten the screw to a torque of 2.70 0.25 mm (24 2 lb in). Do nottighten any of the screws in the levers. 10. Install shaft assembly (9) in the pump housing; then one lever (11); then through crossover lever (10); then through three levers (11) as shown. Install the screw in crossover lever (10). Tighten the screw to a torque of 2.8 0.2 N m (24 2 lb in). Do nottighten any of the screws in the levers.11. After installation of the governor, fuel injection pumps and fuel transfer pump, adjust the fuel pump calibration, the crossover levers, the fuel setting and the high and low idle speeds. See the Systems Operation Testing & Adjusting Manual.End By:a. install fuel transfer pumpb. assemble governorc. install fuel injection pump
Put clean fuel on all parts during assembly.1. Use Tooling (A) to install the camshaft front bearing in the housing. Install the bearing with the chamfer toward the inside of the pump housing.2. Install the bearing so it is even with the front face of the pump housing. 3. Use Tooling (B) to machine the bore in the camshaft front bearing to the correct size. See Special Instruction, SMHS6735 for the procedure to machine the new camshaft front bearing. The bore in the bearing must be 25.413 0.013 mm (1.0005 .0005 in). 4. Use Tooling (A) to install the camshaft rear bearing in the housing. Install the bearing so groove (1) in the bearing is in the position shown. On earlier pump housings without a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.114 0.025 mm (.0045 .0010 in)below face (X) on the housing. On later pump housings with a thrust washer, install the bearing into the bore so the outer face of the bearing is 0.43 0.13 mm (.017 .005 in)below the counterbore for the thrust washer. 5. Install thrust washer (2) in the housing with the ear on the thrust washer in the hole in the pump housing so the thrust washer will not turn.6. With the pump housing in a vertical position as shown, carefully install camshaft (3). To make sure that the thrust washer will be kept in its correct installation location, keep the pump housing in a vertical position, and install the fuel transfer pump and camshaft sleeve. See Fuel Transfer Pump Installation for the procedure to install the fuel transfer pump and camshaft sleeve.
If the pump housing is assembled while it is in a horizontal position, the thrust washer can slide out of the counterbore and into the area between the camshaft thrust face and the housing. Then the fuel pump camshaft end play will not be correct, and it will be necessary to disassemble the fuel pump housing so the thrust washer can be installed correctly.
7. Install each roller (4) in their respective lifters. 8. Use a magnet to install lifter assemblies (5) in their respective bores in the pump housing with the groove in each lifter in alignment with the dowel in the lifter bore. 9. Install shaft (6) in the pump housing; then through one lever (7); then through crossover lever (8); then through three levers (7) as shown. Install the screw in crossover lever (8). Tighten the screw in crossover lever (8). Tighten the screw to a torque of 2.70 0.25 mm (24 2 lb in). Do nottighten any of the screws in the levers. 10. Install shaft assembly (9) in the pump housing; then one lever (11); then through crossover lever (10); then through three levers (11) as shown. Install the screw in crossover lever (10). Tighten the screw to a torque of 2.8 0.2 N m (24 2 lb in). Do nottighten any of the screws in the levers.11. After installation of the governor, fuel injection pumps and fuel transfer pump, adjust the fuel pump calibration, the crossover levers, the fuel setting and the high and low idle speeds. See the Systems Operation Testing & Adjusting Manual.End By:a. install fuel transfer pumpb. assemble governorc. install fuel injection pump
Parts shaft Volvo Penta:
21951469
21951469 Shaft kit
AQD70D; TAMD70D; TAMD70E, D12D-A MH; D12D-B MH; D12D-C MH, D9A2A; D9A2A D9-425; D9A2A D9-500, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD16
806119
806119 Shaft
D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TD100CHC; TD100CRC; TD121CHC, TMD100C, TMD102A; TAMD102A;
6603896
6603896 Shaft
D100A; D100AK; D100B, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, MD120A; MD120AK; TMD120A, TAD1030P, TAD1230P; TD121GP-87; TWD1210P, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAD1641VE; TAD1642VE; TAD1643VE, TAD940GE; TAD94
241783
241783 Shaft
D100A; D100AK; D100B, D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TAMD61A; TAMD62A, TAMD71A; TAMD72A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TD100G-87; TD1030ME; TWD1030M
863015
863015 Shaft
TAD1030P, TAD1230P; TD121GP-87; TWD1210P, TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAD1641VE; TAD1642VE; TAD1643VE, TAD940GE; TAD941GE, TAD940VE; TAD941VE; TAD942VE, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; T
862441
862441 Shaft
TAD1230P; TD121GP-87; TWD1210P, TAMD162A; TAMD162B; TAMD162C, TAMD74A; TAMD74A-A; TAMD74A-B, TD120HP-86; TD121; TD121G, TD121G-87; TWD1210V; TWD1211V, TID162AG; TID162AGP; TID162AP, TWD1620G; TWD1630G; TAD1630G
1543551
1543551 Shaft
TAD1630P; TWD1630P; TWD1630PP, TAD1630V; TWD1630V, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TID162AG; TID162AGP; TID162AP, TWD1620G; TWD1630G; TAD1630G
1675920
1675920 Shaft
TAD1630P; TWD1630P; TWD1630PP, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P, TD164KAE, TID162AG; TID162AGP; TID162AP, TWD1620G; TWD1630G; TAD1630G