7736260_147 Volvo.Penta shield with mounting components


7736260_147 shield with mounting components Volvo.Penta 430; 430A; 430B shield
7736260_147 shield with mounting components Volvo Penta
Rating:
8

Buy shield with mounting components 7736260_147 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

430; 430A; 430B   Volvo.Penta

Volvo Penta entire parts catalog list:

430; 430A; 430B; 431A; 431B; 432A; 434A; 500B; 501B; 570A; 572A; 740B; DP-A; DP-A1; DP-A2; DP-C; DP-C1; DP-C1 1.95; DP-C1 2.30; DP-D; DP-D1; DP-D1

Information:

The following background information is related to this procedure:Injector codes are 30 hexadecimal character codes that are supplied with each injector. The code is on a plate on the top of the injector and a card is also included in the packaging for the injector. The code is used by the ECM to balance the performance of the injectors.Refer to Troubleshooting, "Injector Code - Calibrate" for further information.
Illustration 1 g02131289
Typical code plate on an injector
Illustration 2 g02132293
Sequence for recording the injector code
During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Active Diagnostic Codes
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position.
C. Check for active diagnostic codes or recently logged diagnostic codes.
Diagnostic codes
Result: No diagnostic codes are present.
Return the unit to service.
Result: One or more of the preceding diagnostic codes are active.
Make a note of any cylinder numbers with the active diagnostic code. Proceed to Test Step 2.
2. Check the Injector Code on any Suspect Cylinders
A. Connect the electronic service tool to the diagnostic connector. Refer to Troubleshooting, "Electronic Service Tools".
B. Turn the keyswitch to the ON position.
C. Select the following menu options on the electronic service tool to obtain the injector codes from the ECM:
"Service"
"Calibrations"
"Injector Trim Calibration"
D. Make a note of the injector codes for any suspect cylinders.
Diagnostic code
Result: The card that was supplied with the injector is available for the suspect cylinders.
Repair: Compare the injector code from the card with the injector code that was recorded from the electronic service tool for each suspect cylinder.
If the codes match, proceed to Test Step 3.
If the codes do not match, then use the electronic service tool to input the code from the card.
Result: The card with the injector code is not available.
Proceed to Test Step 3.
3. Manually Program the Injector Code
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install".
B. Make a note of the injector code that is on the injector in any suspect cylinders.
Note: Refer to Illustration 2 for the correct sequence for recording the injector code.
C. Compare the injector code from the injector with the injector code from the electronic service tool for each suspect cylinder.
Injector codes
Result: The code on the injector is the same as the code in the ECM. The injector is incorrect for the engine.
Repair: Replace the injector with the correct injector for the engine. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: The code on the injector is not the same as the code in the ECM.
Repair: Use the electronic service tool to input the correct injector code. Refer to Troubleshooting, "Injector Code - Calibrate" for the correct procedure.
Use the electronic service tool to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
If the procedure did not correct the issue, contact the Dealer Solutions Network (DSN).


Parts shield Volvo Penta:

876630
Shield
876630 Shield
430; 430A; 430B, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
876510
Shield
876510 Shield
230A; 230B; 250A, 430; 430A; 430B, 740A; BB740A, KAD42A; KAMD42A; HS1A, MD31A; TMD31B; TAMD31B, TMD41B; D41B; TAMD41B
876150
 
876150 Shield kit
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ231A; AQ231B; AQ231LB, AQ271A; AQ271B; AQ271C, AQ311A; AQ311B
841781
 
841781 Shield
430; 430A; 430B, 500; 500A; 501A, 571A, AQ175A, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C, AQ290A, AQ311A; AQ311B
7736260_146
Back to top