3582093 Volvo.Penta Shim

Illustration 1 g01072831
Test Step 1. Check for Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Turn the keyswitch to the ON position.
Verify whether any of the following diagnostic codes are active or logged.
320-02
320-11
342-02
342-11
If the diagnostic code is logged but not active, run the engine until the engine is at normal operating temperature. The problem may only occur when the engine is at the normal operating temperature.
If the engine will not start, monitor the engine speed on Cat ET while the engine is being cranked. Cat ET may need to be powered from another battery while the engine is being cranked in order to ensure that Cat ET does not reset.Note: Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message will be replaced with an engine speed once the ECM is able to calculate a speed from the signal.Expected Result:One or more of the diagnostic codes that are listed above are logged or active.Results:
Diagnostic Codes - There is a logged diagnostic code or an active diagnostic code for the engine speed/timing sensors. Proceed to Test Step 3.
No Diagnostic Codes - There are no diagnostic codes for the engine speed/timing sensors, but the engine is not running properly.Repair: Proceed to the appropriate topic in Troubleshooting, "Troubleshooting without a Diagnostic Code".STOP
No Engine rpm - Engine rpm is not indicated on Cat ET. Proceed to Test Step 2.Test Step 2. Check the Installation of the Sensors and the Brackets
Illustration 2 g00810795
Sensors and mounting brackets (typical example)
The flange of the sensor should be flush against the engine in order to ensure proper operation.
Inspect the bracket in order to ensure that the installation allows the flange of the sensor to be flush against the engine.Verify that the bracket is not bent.Note: The bracket cannot be replaced separately.
Ensure that the O-ring has been installed on the sensor, and ensure that the O-ring is free of damage.
If either of the following diagnostic codes is active, there may be a problem with the assembly of the camshaft gear or the crankshaft gear:
320-11
342-11Refer to Illustration 2.Expected Result:The sensors and the bracket are properly installed.Results:
OK - The sensors and the bracket are properly installed. Proceed to Test Step 3.
Not OK - The sensors and/or the bracket are not properly installed.Repair: Perform the following procedure in order to properly install the sensors and the bracket:
Loosen the bolt that holds the sensor mounting bracket to the engine.
Seat the sensor and tighten the bolt.If the sensor will not seat, repair the sensor or replace the sensor, as required.Note: The sensor must not be removed from the bracket.
Ensure that the sensor is properly oriented and that the harness is secured in the proper location.
Verify that the repair eliminates the problem.STOPTest Step 3. Measure the Sensor Resistance at the ECM Connector
Illustration 3 g01055967
ECM connector P2
Turn the keyswitch to the OFF position.
Thoroughly inspect the J2/P2 ECM connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on the following wires in the P2 ECM connector that are associated with the suspect engine speed/timing sensors.Refer to Illustration 3.
Ensure that the latch tab on the connector is properly latched and ensure that the latch tab is fully latched.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Repair the harness or repair the connector if a problem is found.
Ensure that the wiring harness is correctly routed and secured at the proper locations.
Ensure that the harness wiring is not pulled too tightly. When the harness wiring is pulled too tightly, vibrations or movement can cause intermittent connections.
Inspect the harness wiring for nicks and for abrasions.
If the harness and the connector are okay, disconnect ECM connector J2/P2.
Use the following procedure to measure the circuit resistance for the primary engine speed/timing sensor:Refer to Illustration 3.
Measure the resistance between P2-48 (primary engine speed/timing +) and P2-49 (primary engine speed/timing −).Note: Check for an intermittent problem (open or short) by moving the harness while you measure the resistance. Pull the wires that are directly behind the sensors and shake the wires that are directly behind the sensors.Resistance ... 75 to 230 Ohms
Use the following procedure