3884689 Volvo.Penta Shim


3884689 Shim Volvo.Penta IPS15-A, IPS15-B, IPS2-A, IPS2-B, IPS2-C, IPS20-D, IPS3-A, IPS3-C, IPS30-D Shim
3884689 Shim Volvo Penta
Rating:
78

Buy Shim 3884689 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The removal procedure is identical for the two cylinder, the three cylinder and the four cylinder engines. The illustrations show the four cylinder engine.
Clean the bottom face of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place an identification mark on the heads of the valves for installation purposes. Note: The head of the inlet valve has a larger diameter than the head of the exhaust valve.
Position the cylinder head on a suitable surface with the valve springs facing upward. Note: Ensure that the machined face of the cylinder head is kept on a clean, soft surface in order to prevent damage to the machined surface.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 1 g01129177
Typical example
Install tool (A) in position on the cylinder head in order to compress the appropriate valve spring (3).
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Apply pressure to tool (A). Remove the valve keepers (1).
Slowly release the pressure on tool (A).
Illustration 2 g01129220
Typical example
Remove the valve spring retainer (2).
Remove valve spring (3).
Repeat steps 4 to 8 for the remaining valves.
Remove tool (A).
Remove the valve stem seals (4).
Carefully turn over the cylinder head.
Remove the valves (5). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The installation procedure is identical for the two cylinder, the three cylinder and the four cylinder engines. The illustrations show the four cylinder engine.
Clean all parts. Ensure that all ports, all coolant passages and all lubrication passages are free from debris. To inspect the cylinder head, refer to Testing and Adjusting, "Cylinder Head Inspect" for further information.
Inspect all of the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and refer to Testing and Adjusting, "Valve Depth - Inspect " for further information.
Inspect all of the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and refer to Testing and Adjusting , "Valve Guide - Inspect" for further information.
Illustration 3 g01129220
Typical example
Lubricate the stems of all valves (5) with clean engine oil. Install the valves (5) in the appropriate positions.
Carefully turn over the cylinder head and ensure that all of the valves remain in place.
Use a suitable tool to install the new valve stem seals (4) onto each of the valve guides. Note: The outer face of the valve guides must be clean and dry before installing the valve stem seals (4). The inlet valve stem and the exhaust valve stem use seals that are different parts.
Inspect the valve springs (3) for wear and for the correct installed length. Refer to Specifications, "Cylinder Head Valves " for further information.
Install the valve spring (3) onto the cylinder head.
Install the valve spring retainer (2).
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Illustration 4


Parts shim Volvo Penta:

983159
 
983159 Shim
DPH-A; TSK DPH-B; TSK DPH-A, DPH-D; DPR-D; DPH-D1, IPS-A, IPS-B, IPS-C, IPS-D, IPS-E, IPS-F, IPS15-A, IPS15-B
983160
Shim
983160 Shim
DPH-A; TSK DPH-B; TSK DPH-A, DPH-D; DPR-D; DPH-D1, IPS-A, IPS-B, IPS-C, IPS-D, IPS-E, IPS-F, IPS15-A, IPS15-B
991100
Shim
991100 Shim
IPS15-A, IPS15-B, IPS2-A, IPS2-B, IPS2-C, IPS20-D, IPS3-A, IPS3-C, IPS30-D
3884190
 
3884190 Shim
IPS15-A, IPS15-B, IPS2-A, IPS2-B, IPS2-C, IPS20-D, IPS3-A, IPS3-C, IPS30-D
21211765
 
21211765 Shim
IPS-A, IPS-B, IPS-C, IPS-D, IPS-E, IPS-F, IPS15-A, IPS15-B, IPS2-A, IPS2-B, IPS2-C, IPS20-D, IPS3-A, IPS3-C, IPS30-D
21157128
 
21157128 Shim
IPS-A, IPS-B, IPS-C, IPS-D, IPS-E, IPS-F, IPS15-A, IPS15-B, IPS2-A, IPS2-B, IPS2-C, IPS20-D, IPS3-A, IPS3-C, IPS30-D
991097
 
991097 Shim
IPS2-A, IPS2-B, IPS2-C, IPS20-D, IPS3-A, IPS3-C, IPS30-D
991098
 
991098 Shim
IPS2-A, IPS2-B, IPS2-C, IPS20-D, IPS3-A, IPS3-C, IPS30-D
Back to top