21738263 Solenoid valve Volvo.Penta
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE, TAD750VE; TAD760VE
Solenoid
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
VIIKEND Solenoid Valve 0928400670 21738263 Compatible with Volvo DD120C DD140C EC140D EC140E EC160D EC160E EC180D EC180E EC200D EC220D EC220E EC235D EC250D EC250E
VIIKEND Part Name: Solenoid Valve || Part Number: 0928400670 21738263 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Applicable: Compatible with Volvo ECR235D ECR235E EW140D EW140E EW160D EW160E EW180D || Compatible with Volvo DD120C DD140C EC140D EC140E EC160D EC160E EC180D EC180E EC200D EC220D EC220E EC235D EC250D EC250E EC300D EC300E EC350D ECR145D ECR145E || Package included: 1pcs Solenoid Valve 0928400670 21738263
VIIKEND Part Name: Solenoid Valve || Part Number: 0928400670 21738263 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Applicable: Compatible with Volvo ECR235D ECR235E EW140D EW140E EW160D EW160E EW180D || Compatible with Volvo DD120C DD140C EC140D EC140E EC160D EC160E EC180D EC180E EC200D EC220D EC220E EC235D EC250D EC250E EC300D EC300E EC350D ECR145D ECR145E || Package included: 1pcs Solenoid Valve 0928400670 21738263
Nayuank Solenoid Valve 0928400670 21738263 Fits For Volvo DD120C DD140C EC140D EC140E EC160D EC160E EC180D EC180E EC200D EC220D EC220E EC235D EC250D EC250E
Nayuank Part Name: Solenoid Valve || Part Number: 0928400670 21738263 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Applicable: Fits For Volvo ECR235D ECR235E EW140D EW140E EW160D EW160E EW180D || Fits For Volvo DD120C DD140C EC140D EC140E EC160D EC160E EC180D EC180E EC200D EC220D EC220E EC235D EC250D EC250E EC300D EC300E EC350D ECR145D ECR145E || Package included: 1pcs Solenoid Valve 0928400670 21738263
Nayuank Part Name: Solenoid Valve || Part Number: 0928400670 21738263 Note: Please check the fitment carefully before purchase. Or just tell us the part number you need. || Applicable: Fits For Volvo ECR235D ECR235E EW140D EW140E EW160D EW160E EW180D || Fits For Volvo DD120C DD140C EC140D EC140E EC160D EC160E EC180D EC180E EC200D EC220D EC220E EC235D EC250D EC250E EC300D EC300E EC350D ECR145D ECR145E || Package included: 1pcs Solenoid Valve 0928400670 21738263
Manifold Pressure Intake MAP Sensor HIGH Flow in-Tank Fuel Pump E85/ Compatible 340LPH MAP Pressure Sensor
XCSZWTY Features & Quality Manifold air pressure sensor has high reliability and stability, long in working life with temperature compensation, high level of accuracy. || Part Number:0928400670, 0 928 400 670, 134 0622, 1340622, 20794130, 20993071, 21060258, 0928400784 VOE21738263,VOE 21738263, 21738263, 01340622,0134 0622 || /Fit For 05.2006- For VOLVO FE FE 240-18 177 240 7100 || /Fit For 05.2006- For VOLVO FE FE 240-22 177 240 7100 || Easy to install: You can replace parts by yourself, just need to remove the old parts, solve the vehicle problems by yourself, thus saving you a lot of money and time.
XCSZWTY Features & Quality Manifold air pressure sensor has high reliability and stability, long in working life with temperature compensation, high level of accuracy. || Part Number:0928400670, 0 928 400 670, 134 0622, 1340622, 20794130, 20993071, 21060258, 0928400784 VOE21738263,VOE 21738263, 21738263, 01340622,0134 0622 || /Fit For 05.2006- For VOLVO FE FE 240-18 177 240 7100 || /Fit For 05.2006- For VOLVO FE FE 240-22 177 240 7100 || Easy to install: You can replace parts by yourself, just need to remove the old parts, solve the vehicle problems by yourself, thus saving you a lot of money and time.
Compatible models:
Volvo Penta entire parts catalog list:
- Fuel Pressure Regulator » 21738263
TAD734GE
TAD750VE; TAD760VE
Information:
1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap.2. Remove bearing caps No. 2 through No. 4. Remove thrust plates from No. 3 upper bearing.
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 270 lb. (122 kg). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 400°F (204°C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows: a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.006 to 0.020 in. (0.152 to 0.508 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 270 lb. (122 kg). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 400°F (204°C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2).4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS.6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block. 8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block.9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows: a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.006 to 0.020 in. (0.152 to 0.508 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump
Parts solenoid Volvo Penta:
20795296
20933795