3582906 Volvo.Penta Spacer ring


3582906 Spacer ring Volvo.Penta 120S-A; 120S-B; 120S-D, 130S-C; 130SR-C, 130S; 130S-B; 130SR-A, 150S-C; 150SR-C, 150S; 150S-B; 150SR Spacer
3582906 Spacer ring Volvo Penta
Rating:
58

Buy Spacer ring 3582906 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Information:


Illustration 1 g00760014
Oil pressure map for C-10 and C-12 Industrial Engines C-15 and C-16 EnginesThe Electronic Control Module (ECM) detects all of the following conditions:
Engine oil pressure is below the line for "Shutdown" in Illustration 2 for ten seconds.
The engine has been running for at least ten seconds. This ten second delay begins once the engine speed is within 50 rpm of low idle.
Illustration 2 g00760031
Oil pressure map for C-15 and C-16 Industrial EnginesSystem Response:The ECM will log the shutdown.The engine will shut down.
There may be a problem with the engine lubrication system.
There may be a problem with the engine oil pressure sensor.Test Step 1. Check the Engine Oil Level
Check the engine oil level.Expected Result:The engine oil level is OK.Results:
OK - The engine oil level is OK. Proceed to Test Step 2.
Not OK - The engine oil level is low.Repair: Add engine oil to the proper level.STOPTest Step 2. Verify Proper Sensor Installation
Check the installation of the engine oil pressure sensor.
Check the wiring of the engine oil pressure sensor. Refer to the Electrical Schematic for the proper wiring. Ensure that all of the wires and connectors are properly connected.Expected Result:The sensor is properly installed and the wiring is correct.Results:
OK - The sensor is properly installed. Proceed to Test Step 3.
Not OK - The sensor is not installed properly.Repair: Install the engine oil pressure sensor properly. Repair the wiring and/or the connectors to the sensor.Verify that the repair eliminates the problem.STOPTest Step 3. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Check for active diagnostic codes that are related to the atmospheric pressure sensor and/or to the turbocharger outlet pressure sensor.Expected Result:There are no diagnostic codes that are related to the atmospheric pressure sensor and/or to the turbocharger outlet pressure sensor.Results:
OK - There are no diagnostic codes. Proceed to Test Step 4.
Not OK - There is a diagnostic code that is related to the atmospheric pressure sensor and/or to the turbocharger outlet pressure sensor.Repair: Troubleshoot the diagnostic code before continuing with this procedure.STOPTest Step 4. Check the Status Screen
Turn the keyswitch to the ON position. The engine should be off.
Monitor the status for "Boost Pressure" and "Engine Oil Pressure" on Cat ET.Expected Result:"Boost Pressure" and "Engine Oil Pressure" are less than 10 kPa (2 psi).Results:
OK - The boost pressure and the engine oil pressure are less than 10 kPa (2 psi). Proceed to Test Step 6.
Not OK - Boost Pressure - The boost pressure is greater than 10 kPa (2 psi). Proceed to Test Step 8.
Not OK - Engine Oil Pressure - The engine oil pressure is greater than 10 kPa (2 psi). Proceed to Test Step 9.
Not OK - Both - The boost pressure and engine oil pressure are greater than 10 kPa (2 psi). Proceed to Test Step 5.Test Step 5. Check the Supply Voltage to the Pressure Sensors
Disconnect the atmospheric pressure sensor, the engine oil pressure sensor, and the turbocharger outlet pressure sensor.
Turn the keyswitch to the ON position.
Measure the voltage between terminal A (+5V) and terminal B (Common) of each pressure sensor connector on the engine harness.Expected Result:The voltage is 5.0 0.16 VDC.Results:
OK - The voltage is within the range.Repair: Reconnect the engine oil pressure sensor and the turbocharger outlet pressure sensor.Temporarily connect a new atmospheric pressure sensor.If the new sensor fixes the problem, reconnect the suspect sensor.If the problem returns, permanently replace the sensor.Verify that the repair eliminates the problem.STOP
Not OK - There is a problem with the 5 volt supply.Repair: Check the J2/P2 ECM connector and the sensor connectors for corrosion and for moisture.Check the 5


Parts spacer Volvo Penta:

889738
 
889738 Spacer ring
120S-A; 120S-B; 120S-D, 130S-C; 130SR-C, 130S; 130S-B; 130SR-A
3582887
 
3582887 Spacer
120S-A; 120S-B; 120S-D, 130S-C; 130SR-C, 130S; 130S-B; 130SR-A, 150S-C; 150SR-C, 150S; 150S-B; 150SR
3582914
 
3582914 Spacer
120S-A; 120S-B; 120S-D, 130S; 130S-B; 130SR-A
3582880
 
3582880 Spacer
120S-A; 120S-B; 120S-D, 130S; 130S-B; 130SR-A
3586509
 
3586509 Spacer
130S-C; 130SR-C, 150S-C; 150SR-C, 150S; 150S-B; 150SR
3586555
 
3586555 Spacer
150S-C; 150SR-C, 150S; 150S-B; 150SR
Back to top