912129 Spacer ring Volvo.Penta
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, MD100A; TMD100A; TMD100AK
Spacer
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$148.32
19-11-2022
7.7823[3.50] Pounds
-: -
One-Piece clamp Coupling MAS Both Sides bore 50mm Without Keyway Made of Steel 1.0718 with Bolts DIN 912-12.9
Material: Steel 1.0718 burnished. Temperature range from -40°C to +175°C. Maximum speed 40
Material: Steel 1.0718 burnished. Temperature range from -40°C to +175°C. Maximum speed 40
$47.57
19-11-2022
0.6172[0.28] Pounds
-: -
One-Piece clamp Coupling MAS Both Sides bore 15mm with Keyway Made of Steel 1.0718 with Bolts DIN 912-12.9
Material: Steel 1.0718 burnished. Temperature range from -40°C to +175°C. Maximum speed 400
Material: Steel 1.0718 burnished. Temperature range from -40°C to +175°C. Maximum speed 400
Compatible models:
Volvo Penta entire parts catalog list:
- Induction- and Exhaust Manifold, Classed Engine: A » 912129
- Induction- and Exhaust Manifold, Classed Engine: B
- Induction- and Exhaust Manifold, Classed Engine: C
MD100A; TMD100A; TMD100AK; TMD100A-CC; MD100B; MD100BK; MD100B-CC
Information:
Table 1
J1939 Code and Description CDL Code and Description Comments
8149-5
Aftertreatment DEF Doser Ready Status : Current Below Normal 3583-5
Switch Panel #1 : Current Below Normal
8149-6
Aftertreatment DEF Doser Ready Status : Current Above Normal 3583-6
Switch Panel #1 : Current Above Normal
Table 2
Troubleshooting Steps Value Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the dosing cabinet service port connector.
B. Determine if the code is logged or active.
Codes
Result: A -5 code is present.
Proceed to Test Step 2.
Result: A -6 code is present.
Proceed to Test Step 3.
2. Check the Wiring for an Open Circuit
A. Verify that the harness connector is free of debris, corrosion, and secured.
B. Remove the electrical power from the Selective Catalyst Reduction (SCR) Controller.
C. Disconnect connector PR-C674 from the aftertreatment wiring harness.
D. Install a jumper wire between the terminals E and F of the aftertreatment harness connector PR-C674. The aftertreatment harness is replaced with a short circuit.
E. Restore the electrical power to the ECM.
F. Connect Cat ET to the dosing cabinet service port connector.
G. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Note: Wait at least 30 seconds in order for the diagnostic code to be-come active.
Create a Short
Result: A -5 code became active.
The SCR controller did not detect the jumper wire. There is an open circuit between the aftertreatment wiring harness connector PR-C674 and the SCR ECM connector J1 PR-C5. There might be a problem with a connector.
Repair: Repair or replace the connectors or wiring.
Proceed to Test Step 4.
Result: A -6 code became active.
The SCR Controller detected the jumper wire. The wiring between the Selective Catalyst Reduction Controller and the PR-C674 connector is OK. There is a problem with the Aftertreatment Doser Ready Status input circuit between the PR-C674 connector and the customer connection.
Repair: Repair or replace the wiring harness between the PR-C674 connector and the customer connection.
Proceed to Test Step 4.
3. Check the Wiring to the Engine Harness for a Short Circuit
A. Turn keyswitch to OFF.
B. Disconnect connector PR-C674 from the aftertreatment wiring harness.
C. Turn keyswitch to ON.
D. Connect Cat ET using the dosing cabinet service port connector.
E. Monitor the active diagnostic code screen on Cat ET. Check and record any active diagnostic codes.
Short Circuit
Result: A -5 code became active.
The wiring between the Selective Catalyst Reduction Controller and the PR-C674 connector is OK. There is a problem with the Aftertreatment Doser Ready Status input circuit between the PR-C674 connector and the customer connection.
Repair: Repair or replace the wiring harness between the PR-C674 connector and the customer connection.
Proceed to Test Step 4.
Result: A -6 code became active.
There is a short circuit in the wiring between the aftertreatment wiring harness connector PR-C674 and the SCR System ECM connector J1PR-C5. There may be a problem with a connector.
Repair: Repair or replace the connectors or wiring.
Proceed to Test Step 4.
4. Check for Codes
A. Connect Cat ET to the dosing cabinet service port connector.
B. Determine if the code is logged or active.
Codes
Result: No codes are present.
Return to service.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Parts spacer Volvo Penta:
820507
820507 Spacer sleeve
D100A; D100AK; D100B, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD11; MD11C; MD11D
843716
842899
842899 Spacer sleeve
D100BHC; D100BRC; TD100AHC, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TD100CHC; TD100CRC; TD121CHC, TD120AHC; TD120ARC; TAD120AHC, TMD100C, TMD102A; TAMD
842902
842902 Spacer sleeve
D100BHC; D100BRC; TD100AHC, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, TD120AHC; TD120ARC; TAD120AHC
823083
823083 Spacer ring
MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TMD100C, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
408519
330292
823202