983740 Spacer sleeve Volvo.Penta
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GXi-C; 4.3GXi-CF; 4.3GXi-D, 4.3GXi-E; 4.3GXi-EF; 4.3OSi-E, 4.3GXi-F; 4.3GXi-FF; 4.3OSi-F, 4.3GXi-G; 4.3GXi-GF; 4.3OSi-G, 4.3GXi-J; 4.3GXi-JF; 4.3OSi-J, 5.0GL-F; 5.
Spacer
Price: query
Rating:
Number on catalog scheme: 35
Compatible models:
4.3GL-A; 4.3GL-B; 4.3GL-C
4.3GL-E; 4.3GL-EF
4.3GL-G; 4.3GL-GF
4.3GL-J; 4.3GL-JF
4.3GXi-C; 4.3GXi-CF; 4.3GXi-D
4.3GXi-E; 4.3GXi-EF; 4.3OSi-E
4.3GXi-F; 4.3GXi-FF; 4.3OSi-F
4.3GXi-G; 4.3GXi-GF; 4.3OSi-G
4.3GXi-J; 4.3GXi-JF; 4.3OSi-J
5.0GL-F; 5.0GL-FF
5.0GL-H; 5.0GL-HF
5.0GL-J; 5.0GL-JF
5.0GXi-C; 5.0GXi-CF; 5.0GXi-D
5.0GXi-E; 5.0GXi-EF; 5.0OSi-E
5.0GXi-F; 5.0GXi-FF; 5.0OSi-F
5.0GXi-G; 5.0GXi-GF; 5.0OSi-G
5.0GXi-J; 5.0GXi-JF; 5.0OSi-J
5.0GXiC-J; 5.0GXiC-JF; 5.0GiC-J
5.0GXiCE-J; 5.0GXiCE-JF; 5.0GXiCE-M
5.0GXiE-JF; 5.0GXiE-J; 5.0OSiE-JF
5.7Gi-300-J; 5.7Gi-300-JF; 5.7OSi-300-J
5.7Gi-C; 5.7Gi-CF; 5.7Gi-D
5.7Gi-E; 5.7Gi-EF; 5.7GiI-E
5.7Gi-F; 5.7Gi-FF; 5.7GXi-G
5.7Gi-G; 5.7Gi-GF; 5.7GXi-H
5.7GiC-300-J; 5.7GiC-300-JF; 5.7GXiC-J
5.7GiCE-300-J; 5.7GiCE-300-JF; 5.7GXiCE-J
5.7GiE-300-J; 5.7GiE-300-JF; 5.7GXiE-J
5.7GL-A; 5.7GL-B; 5.7GL-C
8.1Gi-A; 8.1Gi-B; 8.1Gi-BF
8.1Gi-E; 8.1Gi-EF; 8.1GXi-D
8.1Gi-F; 8.1Gi-FF; 8.1GXi-E
8.1Gi-G; 8.1Gi-GF; 8.1GXi-F
8.1Gi-H; 8.1Gi-HF; 8.1GXi-G
8.1Gi-J; 8.1Gi-JF; 8.1OSi-J
8.1GiC-400-J; 8.1GiC-400-JF; 8.1GiC-400-Q
8.1GiCE-J; 8.1GiCE-JF; 8.1GiCE-M
8.1GiE-JF; 8.1GiE-J; 8.1OSiE-JF
D3-110I-A; D3-110I-B; D3-110I-C
D3-110I-D; D3-110I-E; D3-110I-F
D3-110I-G; D3-140A-G; D3-140I-G
D3-110I-H; D3-140A-H; D3-140I-H
SX-A; DPS-A; DPS-B
TSKs; SX-M; 1998-2005
TSKs; SX-M; 2006-2008
XDP-B; TSK X-B; TSK X-BLT
Volvo.Penta
Volvo Penta entire parts catalog list:
- Jackshaft » 983740
4.3GL-G; 4.3GL-GF
4.3GL-J; 4.3GL-JF
4.3GXi-C; 4.3GXi-CF; 4.3GXi-D; 4.3GXi-DF; 4.3OSi-C; 4.3OSi-CF; 4.3OSi-D; 4.3OSi-DF
4.3GXi-E; 4.3GXi-EF; 4.3OSi-E; 4.3OSi-EF
4.3GXi-F; 4.3GXi-FF; 4.3OSi-F; 4.3OSi-FF
4.3GXi-G; 4.3GXi-GF; 4.3OSi-G; 4.3OSi-GF
4.3GXi-J; 4.3GXi-JF; 4.3OSi-J; 4.3OSi-JF
5.0GL-F; 5.0GL-FF
5.0GL-H; 5.0GL-HF
5.0GL-J; 5.0GL-JF
5.0GXi-C; 5.0GXi-CF; 5.0GXi-D; 5.0GXi-DF; 5.0OSi-C; 5.0OSi-CF; 5.0OSi-D; 5.0OSi-DF
5.0GXi-E; 5.0GXi-EF; 5.0OSi-E; 5.0OSi-EF
5.0GXi-F; 5.0GXi-FF; 5.0OSi-F; 5.0OSi-FF
5.0GXi-G; 5.0GXi-GF; 5.0OSi-G; 5.0OSI-GF
5.0GXi-J; 5.0GXi-JF; 5.0OSi-J; 5.0OSi-JF; 5.0GXi-N
5.0GXiC-J; 5.0GXiC-JF; 5.0GiC-J; 5.0GiC-JF
5.0GXiCE-J; 5.0GXiCE-JF; 5.0GXiCE-M; 5.0GXiCE-MF; 5.0GiCE-J; 5.0GiCE-JF; 5.0GiCE-M; 5.0GiCE-MF
5.0GXiE-JF; 5.0GXiE-J; 5.0OSiE-JF; 5.0OSiE-J; 5.0GXiE-K; 5.0GXiE-KF; 5.0GXiE-M; 5.0GXiE-MF; 5.0GXiE-N
5.7Gi-300-J; 5.7Gi-300-JF; 5.7OSi-300-J; 5.7OSi-300-JF; 5.7GXi-J; 5.7GXi-JF; 5.7OSXi-J; 5.7OSXi-JF; 5.7Gi-300-N; 5.7GXi-N
5.7Gi-C; 5.7Gi-CF; 5.7Gi-D; 5.7Gi-DF; 5.7GiI-C; 5.7GiI-D; 5.7GXi-D; 5.7GXi-DF; 5.7GXi-E; 5.7GXi-EF; 5.7GXiI-D; 5.7GXiI-E; 5.7OSi-B; 5.7OSi-BF
5.7Gi-E; 5.7Gi-EF; 5.7GiI-E; 5.7GXi-F; 5.7GXi-FF; 5.7GXiI-F; 5.7OSi-D; 5.7OSi-DF; 5.7OSXi-D; 5.7OSXi-DF
5.7Gi-F; 5.7Gi-FF; 5.7GXi-G; 5.7GXi-GF; 5.7OSi-E; 5.7OSi-EF; 5.7OSXi-E; 5.7OSXi-EF
5.7Gi-G; 5.7Gi-GF; 5.7GXi-H; 5.7GXi-HF; 5.7OSi-G; 5.7OSi-GF; 5.7OSXi-G; 5.7OSXi-GF
5.7GiC-300-J; 5.7GiC-300-JF; 5.7GXiC-J; 5.7GXiC-JF
5.7GiCE-300-J; 5.7GiCE-300-JF; 5.7GXiCE-J; 5.7GXiCE-JF; 5.7GiCE-300-M; 5.7GiCE-300-MF; 5.7GXiCE-M; 5.7GXiCE-MF
5.7GiE-300-J; 5.7GiE-300-JF; 5.7GXiE-J; 5.7GXiE-JF; 5.7OSiE-300-J; 5.7OSiE-300-JF; 5.7OSXiE-J; 5.7OSXiE-JF; 5.7GiE-300-K; 5.7GiE-300-KF; 5
5.7GL-A; 5.7GL-B; 5.7GL-C; 5.7GL-D; 5.7GL-E; 5.0GL-A; 5.0GL-B; 5.0GL-C; 5.0GL-D; 5.0GL-E
8.1Gi-A; 8.1Gi-B; 8.1Gi-BF; 8.1Gi-C; 8.1Gi-CF; 8.1Gi-D; 8.1Gi-DF; 8.1GSi-A; 8.1GXi-A; 8.1GXi-AF; 8.1GXi-B; 8.1GXi-BF; 8.1GXi-C; 8.1GXi-CF; 8.1
8.1Gi-E; 8.1Gi-EF; 8.1GXi-D; 8.1GXi-DF; 8.1OSi-A; 8.1OSi-AF; 8.1GiI-E; 8.1GXiI-D
8.1Gi-F; 8.1Gi-FF; 8.1GXi-E; 8.1GXi-EF; 8.1GiI-F; 8.1GXiI-E; 8.1OSi-B; 8.1OSi-BF
8.1Gi-G; 8.1Gi-GF; 8.1GXi-F; 8.1GXi-FF; 8.1OSi-C; 8.1OSi-CF
8.1Gi-H; 8.1Gi-HF; 8.1GXi-G; 8.1GXi-GF; 8.1OSi-D; 8.1OSi-DF
8.1Gi-J; 8.1Gi-JF; 8.1OSi-J; 8.1OSi-JF; 8.1GXi-J; 8.1GXi-JF
8.1GiC-400-J; 8.1GiC-400-JF; 8.1GiC-400-Q
8.1GiCE-J; 8.1GiCE-JF; 8.1GiCE-M; 8.1GiCE-MF
8.1GiE-JF; 8.1GiE-J; 8.1OSiE-JF; 8.1OSiE-J; 8.1GXiE-JF; 8.1GXiE-J; 8.1GiE-K; 8.1GiE-KF; 8.1GXiE-K; 8.1GXiE-KF; 8.1GiE-M; 8.1GiE-MF; 8.1GXiE-
D3-110I-A; D3-110I-B; D3-110I-C; D3-130A-A; D3-130I-A; D3-130A-B; D3-130I-B; D3-130A-C; D3-130I-C; D3-160A-A; D3-160I-A; D3-160A-B; D3-160I-
D3-110I-D; D3-110I-E; D3-110I-F; D3-140I-E; D3-140I-F; D3-140A-D; D3-140A-E; D3-140A-F; D3-150I-D; D3-150I-E; D3-150I-F; D3-170I-D; D3-170I-
D3-110I-G; D3-140A-G; D3-140I-G; D3-150I-G; D3-170A-G; D3-170I-G; D3-200A-G; D3-200I-G; D3-220A-G; D3-220I-G
D3-110I-H; D3-140A-H; D3-140I-H; D3-150I-H; D3-170A-H; D3-170I-H; D3-200A-H; D3-200I-H; D3-220A-H; D3-220I-H
SX-A; DPS-A; DPS-B; DPS-B1; DPS-A OXi; DPS-B OX; DPS-B1 OX; FWD; SX-A 1.43; SX-A 1.51; SX-A 1.60; SX-A 1.66; SX-A 1.79; SX-A 1.89; SX-A 1.97; S
TSKs; SX-M; 1998-2005; TSK SX-M; TSK SX-MDA; TSK SX-MDB; TSK SX-MDC; TSK SX-MLT; TSK SX-MHP; TSK SX-MBAC; TSK SX-MACLT; SX-MAC; TSK SX-MAC
TSKs; SX-M; 2006-2008; TSK SX-M; TSK SX-MACLT; TSK SX-MBAC; TSK SX-MHP
XDP-B; TSK X-B; TSK X-BLT; TSK XHP-B; TSK XHP-BLT; TSK XXP-A; TSK XXP-ALT; TSK XXP-D3; XDP-B 1.78; XDP-B 1.95; XDP-B 2.32; XDP-B-D3 2.11; XD
Information:
Drain the Cooling System
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained.
Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Illustration 1 g00750410
(1) Coolant drain
Illustration 2 g00750411
Locations of the cooling system drain plugs
(1) Oil cooler
(2) Jacket water pump
(3) Engine block Note: If the engine has a jacket water heater, drain the coolant from the heater.
Open the coolant drain. Remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Dealer Service Tools Group:Outside U.S.A. (309) 675-6277
Inside U.S.A. 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
CSTG COSA Geneva, Switzerland 41-22-849 40 56
Clean the Cooling System
After the cooling system has been drained, flush the cooling system with clean water in order to remove any debris.
Close the coolant drain. Clean the drain plugs and install the drain plugs.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Open the water inlet for the separate circuit aftercooler (if equipped). Fill the cooling system with clean water. Install the radiator filler cap. Operate the engine until the temperature reaches 49 °C (120 °F) to 66 °C (150 °F).
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained. Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Open the coolant drain. Remove the drain plugs. Allow the coolant to drain. Flush the cooling system with clean water. Close the coolant drain. Install the drain plugs.
Repeat Steps 3, 4, and 5. Fill the Cooling System
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with ELC (Extended Life Coolant). After filling the cooling system, do not install the radiator filler cap.
Open the water inlet for the separate circuit aftercooler (if equipped). Start the engine. Operate the engine in order to purge the air from the cavities of the engine block. Allow the ELC to warm and allow the coolant level to stabilize. Stop the engine.
Check the coolant level. Maintain the coolant to the proper level on the sight gauge (if equipped). If a sight gauge is not equipped, maintain the coolant within 13 mm (.5 inch) below the bottom of the filler pipe.
Clean the radiator filler cap. Inspect the gaskets of the radiator cap. If the gaskets of the radiator filler cap are damaged, discard the old radiator filler cap and install a new radiator filler cap. If the gaskets of the radiator filler cap are not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the radiator filler cap. The correct pressure is stamped on the face of the radiator filler cap. If the radiator filler cap does not maintain the correct pressure, install a new radiator filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained.
Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Illustration 1 g00750410
(1) Coolant drain
Illustration 2 g00750411
Locations of the cooling system drain plugs
(1) Oil cooler
(2) Jacket water pump
(3) Engine block Note: If the engine has a jacket water heater, drain the coolant from the heater.
Open the coolant drain. Remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Dealer Service Tools Group:Outside U.S.A. (309) 675-6277
Inside U.S.A. 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
CSTG COSA Geneva, Switzerland 41-22-849 40 56
Clean the Cooling System
After the cooling system has been drained, flush the cooling system with clean water in order to remove any debris.
Close the coolant drain. Clean the drain plugs and install the drain plugs.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Open the water inlet for the separate circuit aftercooler (if equipped). Fill the cooling system with clean water. Install the radiator filler cap. Operate the engine until the temperature reaches 49 °C (120 °F) to 66 °C (150 °F).
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained. Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Open the coolant drain. Remove the drain plugs. Allow the coolant to drain. Flush the cooling system with clean water. Close the coolant drain. Install the drain plugs.
Repeat Steps 3, 4, and 5. Fill the Cooling System
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with ELC (Extended Life Coolant). After filling the cooling system, do not install the radiator filler cap.
Open the water inlet for the separate circuit aftercooler (if equipped). Start the engine. Operate the engine in order to purge the air from the cavities of the engine block. Allow the ELC to warm and allow the coolant level to stabilize. Stop the engine.
Check the coolant level. Maintain the coolant to the proper level on the sight gauge (if equipped). If a sight gauge is not equipped, maintain the coolant within 13 mm (.5 inch) below the bottom of the filler pipe.
Clean the radiator filler cap. Inspect the gaskets of the radiator cap. If the gaskets of the radiator filler cap are damaged, discard the old radiator filler cap and install a new radiator filler cap. If the gaskets of the radiator filler cap are not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the radiator filler cap. The correct pressure is stamped on the face of the radiator filler cap. If the radiator filler cap does not maintain the correct pressure, install a new radiator filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.
Parts spacer Volvo Penta:
3832907
3832907 Spacer
D3-110I-A; D3-110I-B; D3-110I-C, TAMD63L-A; TAMD63P-A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TAMD72P-A; TAMD72WJ-A, TAMD74A; TAMD74A-A; TAMD74A-B
984644
983741
983741 Spacer sleeve
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GXi-C; 4.3GXi-CF; 4.3GXi-D, 4.3GXi-E; 4.3GXi-EF; 4.3OSi-E, 4.3GXi-F; 4.3GXi-FF; 4.3OSi-F, 4.3GXi-G; 4.3GXi-GF; 4.3OSi-G, 4.3GXi-J; 4.3GXi-JF; 4.3OSi-J, 5.0GL-F; 5.
821539
821539 Spacer sleeve
430; 430A; 430B, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H, D5A-T; D5A-TA; D5A-B TA, D70B; D70B PP; D70B K, D70CHC; D70CR
3594748
3594748 Spacer screw
4.3GXi-225-R; 4.3Gi-200-R, 4.3GXi-P; 4.3GXi-Q, 4.3GXiE-225-R, 4.3GXiE-M, 4.3GXiE-P; 4.3GXiE-Q, 5.0GXi-270-R, 5.0GXi-P, 5.0GXiC-270-R; 5.0GiC-225-S, 5.0GXiC-J; 5.0GXiC-JF; 5.0GiC-J, 5.0GXiC-P, 5.0GXiCE-270-R; 5.0GiCE-225-S, 5.0GXiCE-J; 5.0GXiCE-JF; 5.
3594749
3594749 Spacer screw
4.3GXi-225-R; 4.3Gi-200-R, 4.3GXi-P; 4.3GXi-Q, 5.0GXi-270-R, 5.0GXi-P, 5.0GXiC-270-R; 5.0GiC-225-S, 5.0GXiC-J; 5.0GXiC-JF; 5.0GiC-J, 5.0GXiC-P, 5.0GXiCE-J; 5.0GXiCE-JF; 5.0GXiCE-M, 5.0GXiE-JF; 5.0GXiE-J; 5.0OSiE-JF, 5.7Gi-300-P; 5.7GXi-P, 5.7Gi-300-R
3859010
3859010 Spacer
4.3GXi-B; 4.3GXi-BF; 4.3OSi-B, 4.3GXi-C; 4.3GXi-CF; 4.3GXi-D, 4.3GXi-E; 4.3GXi-EF; 4.3OSi-E, 5.0GXi-B; 5.0GXi-BF; 5.0OSi-B, 5.0GXi-C; 5.0GXi-CF; 5.0GXi-D, 5.0GXi-E; 5.0GXi-EF; 5.0OSi-E, 5.7Gi-C; 5.7Gi-CF; 5.7Gi-D, 5.7Gi-E; 5.7Gi-EF; 5.7GiI-E
3852350
3852350 Spacer
SX-A; DPS-A; DPS-B, SX-C; SX-C1; SX-C2, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3, SX-S; SX-SLT; SX-ST