244971 Volvo.Penta Spring disc

Table 1
J1939 Code and Description    CDL Code and Description    Comments    
105-3
Engine Intake Manifold #1 Temperature : Voltage Above Normal     172-3
Intake Manifold Air Temperature Sensor : Voltage Above Normal     The code is logged.
The ECM detects that the voltage is not in the acceptable range.    
105-4
Engine Intake Manifold #1 Temperature : Voltage Below Normal     172-4
Intake Manifold Air Temperature Sensor : Voltage Below Normal     The code is logged.
The ECM detects that the voltage is not in the acceptable range.    
110-3
Engine Coolant Temperature : Voltage Above Normal     110-3
Engine Coolant Temperature Sensor : Voltage Above Normal     The code is logged if the engine has been running for more than seven minutes and an open circuit has been detected.    
110-4
Engine Coolant Temperature : Voltage Below Normal     110-4
Engine Coolant Temperature Sensor : Voltage Below Normal     The code is logged. The ECM detects voltage that is not in the acceptable range.    
2433-3
Engine Exhaust Manifold Bank #2 Temperature #1 : Voltage Above Normal     828-3
Right Exhaust Temperature Sensor : Voltage Above Normal     The code is logged.
If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value is used.    
2433-4
Engine Exhaust Manifold Bank #2 Temperature #1 : Voltage Below Normal     828-4
Right Exhaust Temperature Sensor : Voltage Below Normal     The code is logged.
If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value is used.    
2434-3
Engine Exhaust Manifold Bank #1 Temperature #1 : Voltage Above Normal     827-3
Left Exhaust Temperature Sensor : Voltage Above Normal     The code is logged.
If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value is used.    
2434-4
Engine Exhaust Manifold Bank #1 Temperature #1 : Voltage Below Normal     827-4
Left Exhaust Temperature Sensor : Voltage Below Normal     The code is logged.
If the signal from the other exhaust temperature sensor is OK, the signal from that sensor is used. If the signal from the other exhaust temperature sensor is not OK, a default value is used.    System OverviewThe sensor signal for the passive sensor is routed from the ECM to terminal 1 of each sensor connector. The sensor return for the passive sensors is routed to the ECM from terminal 2 of each sensor connector.Diagnostics on the Caterpillar Electronic Technician (ET)Wiggle Test - The Wiggle Test allows you to monitor the status of the signals from the sensors.For additional information regarding the Wiggle Test, refer to the documentation that accompanies the Cat ET software.
Table 2
Troubleshooting Test Steps    Values    Results    
1. Check for Diagnostic Trouble Codes
A. Connect to Caterpillar Electronic Technician (ET).
B. Turn the keyswitch to the ON position.
C. Access the "Active Diagnostic Code" screen on Cat ET.
Wait at least 30 seconds in order for the diagnostic codes to become active.
D. Look for these active codes or logged codes:
1. -3
2. -4
   
Codes    
Result: A -3 diagnostic code is active.
Proceed to Test Step 2.
Result: A -4 diagnostic code is active.
Proceed to Test Step 3.
Result: For a diagnostic code that is logged but not currently active.
Proceed to Test Step 4.
   
2. Create a Short at the Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the suspect sensor.
C. Install the jumper wire between terminal 1 (sensor signal) and terminal 2 (sensor return) at the sensor connector.
D. Turn the keyswitch to the ON position.
E. Monitor the diagnostic codes on Cat ET. Check for an active -4 diagnostic code for the suspect sensor.
Wait at least 30 seconds in order for the diagnostic codes to become active.
F. Turn the keyswitch to the OFF position.
   
Short circuit recognized    
Result: The -3 diagnostic code remains active for the suspect sensor.
There is an open in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Result: A -4 diagnostic code became active after creating the short at the sensor connector.
The wiring is OK. Replace the sensor.
Verify that the problem is resolved.
   
3. Create an Open at the Suspect Sensor Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the sensor connector of the suspect sensor with the active -4 diagnostic code.
C. Turn the keyswitch to the ON position.
D. Monitor the diagnostic codes on Cat ET. Check for an active -3 diagnostic code for the suspect sensor.
Wait at least 30 seconds in order for the diagnostic codes to become active.
For a 110-3 code, start the engine and let the engine idle for 7 minutes. The engine must be running for at least 7 minutes in order for the diagnostic to run.
E. Turn the keyswitch to the OFF position.
   
Open circuit recognized    
Result: The -4 diagnostic code remains active for the suspect sensor.
There is an open in the harness. Repair the wiring or replace the harness.
Verify that the problem is resolved.
Result: A -3 diagnostic code became active after disconnecting the sensor.
The wiring is OK. Replace the sensor.
Verify that the problem is resolved.
   
4. Perform the Wiggle Test
Carefully following this procedure is the best way to identify the root cause of an intermittent problem.
A. Turn the keyswitch to the ON position.
B. Use Cat ET to run the "Wiggle Test".
C. Slowly wiggle the wiring and the connectors between the P2 connector and the sensor. Slowly wiggle the wiring and the connectors between the P1 connector and the sensor. Pay particular attention to the wiring near each connector. Be sure to wiggle all of the wiring.
D. As you wiggle the wiring look for these problems.
1. Loose connectors or damaged connectors
2. Moisture on the connectors or the wiring
3. Damage that