3852577 Volvo.Penta Spring

Table 1
Cross-Reference from Event Codes on Cat Data Link to Troubleshooting Procedure    
Code and Description    Troubleshooting Procedure    
E015(2) High Engine Coolant Temperature Derate     Troubleshooting, "Coolant Temperature Is High"    
E017(1) High Engine Coolant Temperature Warning    
E018(2) High Engine Oil Temperature Derate     Troubleshooting, "Oil Temperature Is High"    
E020(1) High Engine Oil Temperature Warning    
E021(2) High Exhaust Temperature Derate     Troubleshooting, "Exhaust Temperature Is High"    
E025(2) High Inlet Air Temperature Derate     Troubleshooting, "Inlet Air Temperature Is High"    
E027(1) High Inlet Air Temperature Warning    
E030(1) High Transmission Oil Temperature Warning     Troubleshooting, "Transmission Oil Temperature Is High"    
E039(2) Low Engine Oil Pressure Derate     Troubleshooting, "Oil Pressure Is Low"    
E053(1) Low Fuel Pressure Warning     Troubleshooting, "Fuel Pressure Is Low"    
E056(1) High Fuel Temperature Warning     Troubleshooting, "Fuel Temperature is High"    
E057(2) Low Engine Coolant Level Derate     Troubleshooting, "Coolant Level Is Low"    
E059(1) Low Engine Coolant Level Warning    
E085(1) Engine Shutdown Overridden     The override switch for an engine shutdown has been activated.    
E096(1) High Fuel Pressure     Troubleshooting, "Fuel Pressure Is High"    
E097(1) Engine Derate Overridden     The override switch for an engine derate has been activated.    
E100(1) Low Engine Oil Pressure Warning     Troubleshooting, "Oil Pressure Is Low"    
E113(1) High Transmission Oil Pressure     Troubleshooting, "Transmission Oil Pressure Is High"    
E119(1) Low Fuel Level     Add fuel to the fuel tank. Refer to the literature that is provided by the OEM of the vessel for the correct procedure.    
E173(1) High Exhaust Temperature Warning     Troubleshooting, "Exhaust Temperature Is High"    
E190(1) Engine Overspeed Warning     Troubleshooting, "Engine Overspeeds"    
E268(1) Unexpected Engine Shutdown     Troubleshooting, "Engine Shutdown Occurrence"    
E552(1) Low Aftercooler Coolant Level Warning     Troubleshooting, "Coolant Level Is Low"    
E552(2) Low Aftercooler Coolant Level Derate    Parts of the Event Code
Event Code - The "E" identifies the code as an event code. The "XXX(X)" represents a numeric identifier for the event code. The fourth "(X)" assigns one of three levels to the active event code according to the severity of the abnormal system condition. This is followed by a description of the code. Refer to the following example:
E360(1) Low Oil Pressure
E360(2) Low Oil Pressure
E360(3) Low Oil PressureThe definition for the levels of severity for an event are defined below:Level 1 - Level 1 alerts the operator that an engine system requires attention. The operator should check the involved system condition or the operator should perform maintenance on the involved system at the earliest possible time.Level 2 - Level 2 requires a change in the operation of the engine or the performance of a maintenance procedure. Failure to correct the problem that caused this warning may result in damage to the engine components.Level 3 - Level 3 requires an immediate safe shutdown of the engine in order to avoid damage to the engine or injury to personnel around the engine. The problem that caused the event must be corrected before engine operation can resume.Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g01365757
Example of the typical operating range of a sensor (1) This area represents the normal operating range of the engine parameter. (2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem. (3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit. Refer to Troubleshooting, "Diagnostic Trouble Code List" for additional information on diagnostic codes.Logged Event Codes
When the Electronic Control Module (ECM) generates an event code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeLogged events are listed in chronological order. The most recent event code is listed first.This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.Clearing Event Codes
A code is cleared from memory when one of the following conditions occur:
The code does not recur for 100 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Always clear logged event codes after investigating and correcting the problem which generated the code.Troubleshooting
For basic troubleshooting of the engine, perform the following steps in order to diagnose a malfunction:
Obtain the following information about the complaint:
The event and the time of the event
Determine the conditions for the event. The conditions will include the engine rpm and the load.
Determine if there are any systems that were installed by the dealer or by the customer that could cause the event.
Determine whether any additional events occurred.
Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.
Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.
Perform a visual inspection. Inspect the following items:
Fuel supply
Oil level
Oil supply
Wiring
ConnectorsBe sure to check the connectors. This is very important for problems that are intermittent. Refer to Troubleshooting, "Electrical Connectors - Inspect".If these steps do not resolve the problem, refer to Table 1 for the procedure to troubleshoot the event code