6603859 Volvo.Penta Spring washer

This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Valve Lash Check
An adjustment is not necessary if the measurement of the valve lash is in the acceptable range in Table 1.
Table 1
Inlet Valves Exhaust Valves
Valve Lash (Stopped Engine) 0.38 0.08 mm
(0.015 0.003 inch) 0.76 0.08 mm
(0.030 0.003 inch)
TC Compression Stroke 1-2-4 1-3-5
TC Exhaust Stroke(1) 3-5-6 2-4-6
Firing Order 1-5-3-6-2-4(2)
(1) 360° from TC compression stroke
(2) The No. 1 cylinder is at the front of the engine.If the measurement is not within this range, an adjustment is necessary. Refer to "Valve Lash Adjustment" for the proper procedure.Valve Lash Adjustment
Illustration 1 g01373511
Cylinder and valve location
(A) Exhaust valves
(B) Inlet valvesUse the following procedure to adjust the valve lash:
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Table 2
C13 Lash Settings
TC Compression Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.635 0.0762 mm (0.025 0.003 inch)
Cylinders 1-2-4 1-3-5
Table 3
C15 and C18 Lash Settings
TC Compression Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.76 0.08 mm
(0.030 0.003 inch)
Cylinders 1-2-4 1-3-5
Adjust the valve lash according to Table 2 for C13 engines. Adjust the valve lash according to Table 3 for C15 and C18 engines.
Lightly tap the rocker arm with a soft mallet. This action will ensure that the lifter roller seats against the base circle of the camshaft.
Loosen the adjustment locknut.
Place the appropriate feeler gauge between rocker arm and the valve bridge. Then, turn the adjustment screw in a clockwise direction. Slide the feeler gauge between the rocker arm and the valve bridge. Continue turning the adjustment screw until a slight drag is felt on the feeler gauge. Remove the feeler gauge.
Tighten the adjustment locknut to a torque of 30 7 N m (22 5 lb ft). Do not allow the adjustment screw to turn while you are tightening the adjustment locknut. Recheck the valve lash after tightening the adjustment locknut.
Remove the timing bolt and turn the flywheel by 360 degrees in the direction of engine rotation. This action will put the No. 6 piston at the top center position on the compression stroke. Install the timing bolt in the flywheel.
Table 4
C13 Lash Settings
TC Exhaust Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.635 0.0762 mm (−.025 0.003 inch)
Cylinders 3-5-6 2-4-6
Table 5
C15 and C18 Lash Settings
TC Exhaust Stroke Inlet Valves Exhaust Valves
Valve Lash 0.38 0.08 mm
(0.015 0.003 inch) 0.76 0.08 mm
(0.030 0.003 inch)
Cylinders 3-5-6 2-4-6
Adjust the valve lash for C13 engines using Table 4. Adjust the valve lash according to Table 5 for C15 and C18 engines.
Lightly tap the rocker arm with a soft mallet. This action will ensure that the lifter roller seats against the base circle of the camshaft.
Loosen the adjustment locknut.
Place the a