859339 Volvo.Penta Spring


859339 Spring Volvo.Penta AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B Spring
859339 Spring Volvo Penta
Rating:
83

Buy Spring 859339 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$50.41
 

15-04-2024
5.05[2.27] Pounds
US: Auto Parts Direct To
APDTY 859339 Power Window Regulator and Motor Assembly Replaces 15135972, 19260050
APDTY Meets Or Exceeds OEM Specs || Factory OEM Fit Form And Function
Number on catalog scheme: 25
 

Volvo Penta entire parts catalog list:

AD31D; AD31D-A; AD31XD; TAMD31D; TMD31D
AD31L-A; AD31P-A; AD41L-A; AD41P-A; D41L-A; TAMD31L-A; TAMD31M-A; TAMD31P-A; TAMD31S-A; TAMD41H-A; TAMD41H-B; TAMD41P-A; TAMD41L-A; TAMD41M-A
MD31A; TMD31A; TMD31B; TAMD31A; TAMD31B; AD31; AQAD31A; AD31B; 290A; DP-A; DP-B; DP-A1; DP-B1; SP-A; SP-A1
MD31A; TMD31B; TAMD31B; AD31B

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-2320     Combination Puller     1    
C
    1P-2321     Combination Puller     1    
9S-9153 Puller Jaws     3    Start By:
Remove the timing gear cover. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".Note: The engine oil pan is facing in the up direction in order to retain the lifters in position for this procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Ensure that the marks on the timing gears are in alignment. Align the fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center position when these marks are in alignment.
Rotate the engine at 180 degrees.
Illustration 1 g00532179
Use Tool (A) to remove bearing (1) from the front of camshaft gear (2) .Note: This step is necessary only if the camshaft gear is equipped with a bearing.
Illustration 2 g00532382
Do not damage the lobes or the bearings when the camshaft is removed or installed.
Position camshaft gear (2) so that the gear's slots align from the top to the bottom. Remove two bolts (3) and the washers that hold thrust plate (4). Carefully remove the camshaft, the thrust plate and the camshaft gear as an assembly.
Remove the 12 valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".
Illustration 3 g00532384
Use tool (C) to remove camshaft gear (2) from camshaft (5). Remove thrust plate (4) .Installation Procedure 1
Note: In this installation procedure, the engine needs to remain in the upside-down position in order to keep the lifters in position while the camshaft is installed.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: During installation, ensure that camshaft (4) is clean and lubricate all of the components with clean engine oil.
Illustration 4 g00532385
Install thrust plate (4) onto camshaft (5) .
Always wear protective gloves when handling parts that have been heated.
Heat camshaft gear (2) in an oven to a maximum temperature of 150 °C (302 °F) and install camshaft gear (2) onto camshaft (5) .
Install the 12 valve lifters. Refer to Disassembly and Assembly, "Lifter Group - Remove and Install".Note: During installation, ensure that the marks on the timing gears are in alignment. Align the fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder is at the top center position when these marks are in alignment.
Carefully install the camshaft assembly into the original location in the cylinder block.Note: Caution must be used when the camshaft is installed in order to not damage the camshaft l


Parts spring Volvo Penta:

941907
Spring washer
941907 Spring washer
120S-A; 120S-B; 120S-D, 130S-C; 130SR-C, 130S; 130S-B; 130SR-A, 150S-C; 150SR-C, 150S; 150S-B; 150SR, 2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 3.0GXiC-J; 3.0GXi-J, 430; 430A; 430B, 5.0GXiC-270-R; 5.0GiC-225-S, 5.0GXiC-J; 5.0GXiC-JF; 5.0GiC-J, 5.0
941906
 
941906 Spring washer
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B,
940280
Spring washer
940280 Spring washer
2001; 2001B; 2001AG, 251A, 500; 500A; 501A, 571A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, A
942336
 
942336 Spring washer
230A; 230B; 250A, 251A, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 430; 430A; 430B, 5.0GXi-A; 5.7Gi-A; 5.7GXi-A, 5.0GXi-B; 5.0GXi-BF; 5.0OSi-B, 5.7Gi-C; 5.7Gi-CF
840686
 
840686 Spring washer
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, TD3
951979
 
951979 Spring pin
2001; 2001B; 2001AG, 430; 430A; 430B, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, TAMD61A; TAMD62A, TAMD71A; TAMD72A, TAMD71B; TAMD73P-A; TAMD73W
941909
 
941909 Spring washer
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 4.3GXi-B; 4.3GXi-BF; 4.3OSi-B, 4.3GXi-C; 4.3GXi-CF; 4.3GXi-D, 4.3GXi-E; 4.3GXi-EF; 4.3OSi-E
814332
Spring
814332 Spring
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A
Back to top