3583837 Volvo.Penta Starter pinion


3583837 Starter pinion Volvo.Penta D1-13; D1-13B; D1-20 Starter
3583837 Starter pinion Volvo Penta
Rating:
93

Buy Starter pinion 3583837 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

D1-13; D1-13B; D1-20   Volvo.Penta

Volvo Penta entire parts catalog list:

D1-13; D1-13B; D1-20; D1-20B; D1-30; D1-30B; D2-40; D2-40B; D1-13F; D1-20F; D1-30F; D2-40F

Information:


Table 1
Diagnostic Codes Table
Code Code Description Conditions Present Response
102-3 Boost Pressure Sensor: Voltage Above Normal (turbocharged versions only) Open circuit or +B short circuit of sensor/harness. Failure of sensor.
Battery voltage is normal. Sensor supply voltage VCC# is normal.
Voltage of boost pressure is 4.9V or above for 3 seconds or more.
System defaults to 65 kPa (9.43 psi).
Warning Level 2
102-4 Boost Pressure Sensor: Voltage Below Normal (turbocharged versions only) Ground short circuit of sensor/harness. Failure of sensor.
Battery voltage is normal. Sensor supply voltage VCC# is normal.
Voltage of boost pressure sensor is 0.2V or below for 3 seconds or more.
System defaults to 65 kPa (9.43 psi).
Warning Level 2
108-3 Barometric Pressure Sensor Error (High Side) Sensor/ECU internal circuit short to +B
Battery voltage is normal
Barometric pressure sensor voltage is 4.850V or more for 3 seconds or more.
Warning Level 2
System defaults to 65 kPa (9.43 psi).
108-4 Barometric Pressure Sensor Error (Low Side) Sensor/ECU internal circuit short to ground.
Battery voltage is normal
Barometric pressure sensor voltage is 0.2V or less for 3 seconds or more.
Warning Level 2
System defaults to 65 kPa (9.43 psi).
132-3 MAF Sensor: Voltage Above Normal Battery voltage is normal
Engine speed is between 800 rpm and 3000 rpm
Target intake mass air flow is 350 or less and it continues for 3 seconds.
Sensor supply voltage is normal.
Mass air flow sensor voltage is 4.9V or more at normal operation for 3 seconds of more. Sensor output is 0.7 times of target value at normal condition.
Engine derates 25%
EGR stops
Intake throttle fully open
Warning Level 3
132-4 MAF Sensor: Voltage Below Normal Battery voltage is normal.
Starter switch signal is not activated.
Sensor supply voltage is normal.
Mass air flow sensor voltage is 0.1 V or less. for 3 seconds or more.
157-3 Rail Pressure Sensor: Voltage Above Normal Battery voltage is normal.
Sensor supply voltage
Voltage of rail pressure sensor is 3.235 V or above. Engine derates 50%
Accelerator limitation: 50%
EGR stops
Intake throttle fully open
Engine forcibly stopped 60 seconds later
157-4 Rail Pressure Sensor: Voltage Below Normal Battery voltage is normal.
Sensor supply voltage is normal.
Voltage of rail pressure sensor is 0.065 V or less.
3251-3 Differential Pressure Sensor: Voltage Above Normal Battery voltage is normal.
Sensor supply voltage is normal.
Starter switch signal is not activated DPF differential pressure sensor voltage is 4.8 V or more for 3 seconds or more. 0 kPa is default value.
Engine derates 25%
Warning Level 2
3251-4 Differential Pressure Sensor: Voltage Below Normal Battery voltage is normal.
Sensor supply voltage is normal.
Starter switch signal is not activated
DPF differential pressure sensor voltage is 0.2 V or less for 3 seconds or more. Note: The -3 codes are open circuit or +B short circuit. The -4 codes are a ground short circuit . These are almost always a harness issue.
Illustration 1 g06111331
Mass air flow sensor
Illustration 2 g06111333
Differential pressure sensor
Illustration 3 g06111336
Rail pressure sensor
Illustration 4 g06111340
Boost pressure sensor
Table 2
Pressure and Voltage Specifications
Engine State DPF Differential Pressure Signal Intake Air Pressure Sensor
Pressure Boost Pressure Sensor Rail Pressure Sensor
Key Switch On Approx .7 V Approx 100 kPa (14.5 psi) Approx 1.0 V Approx 1 V
Engine Running NA 100 to 180 kPa (14.5 to 26.1 psi) 1.0 to 2.2V 1.65 to 1.80 V
No Load Max Speed NA NA NA 2.50-2.85 V
Accelerating (from LI to HI) NA NA NA 2.5-3.3 V
Table 3
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Codes
A. Establish communication between Caterpillar Electronic Technician (ET) and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if


Parts starter Volvo Penta:

3587072
Starter switch
3587072 Starter switch
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D12D-A MH; D12D-B MH; D12D-C MH, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, D5A-T; D5A-TA; D5A-B TA, D5A-T; D5A-TA; D5A-B TA, KAD32
3803904
Starter motor, exch
3803904 Starter motor, exch
D1-13; D1-13B; D1-20, MD2010B; MD2020B; MD2030B
21302969
Starter motor
21302969 Starter motor
D1-13; D1-13B; D1-20
3801350
Starter motor, exch
3801350 Starter motor, exch
D1-13; D1-13B; D1-20
3580212
 
3580212 Starter pinion
D1-13; D1-13B; D1-20, MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
3803584
Starter motor, exch
3803584 Starter motor, exch
D1-13; D1-13B; D1-20, MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
Back to top