834339 Volvo.Penta Starter motor

Do not attempt to assemble this machine until you read and understand the assembly procedure. Improper procedures could result in injury or death.
Before unloading the chassis and components, read the following suggestions, which will make the assembly easier.Previous assembly experience has shown that choosing the correct area is the first step to a smooth, quick assembly.Remove the paint from all contacting surfaces. This is necessary for a good solid joint. Unless specified, all torques are without thread lubricant.Preparation Before Assembly of Machine
A flat, smooth, well-drained area 30 m × 24 m (100 ft. wide × 80 ft. long) is needed. Use the center of the area to set the chassis.Keep the area around the chassis free for the movement of the cranes.As the components are unloaded, set them in a position near the chassis; but not in the way of the cranes. They will not have to be handled again except for installation on the chassis.Set the large wooden boxes of smaller components, sheet metal, mud flaps, and hardware aside and out of the way. Open the boxes to familiarize yourself with their contents. Do not open the bags of hardware. The bags are well marked as to where the contents are used. Place all the bagged hardware in one of the large wooden boxes close to the machine area.As the components are installed, remove the bagged hardware marked for that component from the box.By organizing the hardware as described, the risk of lost hardware is reduced, as well as the time spent searching for parts.The use of these suggestions, the tools and equipment recommended, and a thorough understanding of the Special Instruction will help ensure a smooth, organized assembly.Reference: Parts Manual, Operation and Maintenance Manual, Tool Guide, Truck Service Manual SENR3334 (Air Conditioning & Heating Service Manual, SENR4621 (3500 Vehicular Engines) SENR4705 (Automatic Ether Injection System) and Special Instruction SMHS7867.
Do not let any dirt or foreign material get into the hydraulic system.
Clean all surfaces and remove burrs from all areas where parts are to be installed. Use warm water and detergent to remove the protecting material.Weights
When a hoist is used to lift any part or assembly, stand clear of the area. Be sure the hoist has the capacity to lift a heavy assembly. Approximate weights of the components and assemblies are given below.
785
Chassis module as shipped ... 31 735 Kg (69,900 lb)Engine ... 7,030 Kg (15,500 lb)Torque Converter ... 680 Kg (1500 lb) The weight of the chassis is distributed approximately equally between the front and back lift points.789
Chassis module as shipped ... 42 600 kg (94,000 lb)Engine ... 8,375 Kg (18,500 lb)Torque Converter ... 815 Kg (1800 lb) The weight of the chassis is distributed approximately equally between the front and back lift points.Specifications
785
Empty weight ... 90 845 kg (200,300 lb)Wheel base ... 5 180 mm (203.94 in)Length ... 11 022 mm (433.94 in)Ground to top of canopy ... 5 460 mm (214.96 in)Turning radius ... 30.5 m (100 ft 4 in)Ground to upper edge of body (30 x 51 tires installed) ... 4 906 mm (193.1 in)Outside of body assembly to center of body ... 3 100 mm (122.5 in)789
Empty weight ... 113 400 kg (250,000 lb)Wheel base ... 5 700 mm (224.4 in)Length ... 12 177 mm (479.4 in)Ground to top of canopy ... 5 928 mm (233.4 in)Turning radius ... 27.5 m (90 ft 3 in)Ground to upper edge of body (36 x 51 tires installed) ... 5 304 mm (208.8 in)Outside of body assembly to center of body ... 3220 mm (126.75 in)Necessary Hoist Capacity
Chassis assembly (less cab, platform, etc.).785
To remove the chassis assembly from the lowboy trailer, two hoists with 27 200 kg (60,000 lb) capacity each, are needed.With the differential housing on supports, one hoist with 27 200 kg (60,000 lb) capacity is needed to lift the chassis at the front lifting points.With the front frame crossmember on supports, one hoist with 27 200 kg (60,000 lb) is needed to lift the chassis at the rear lifting points.789
To remove the chassis assembly from the lowboy trailer, two hoists with 36 320 kg (80,000 lb) capacity are needed.With the differential housing on supports, one hoist with 36 320 kg (80,000 lb) capacity is needed to lift the chassis at the front lifting points.With the front frame crossmember on supports, one hoist with 36 320 kg (80,000 lb) is needed to lift the chassis at the rear lifting points.Chassis Lifting Points
1. Lift the chassis assembly from locations (A) and (B) on the left side.2. Lift the chassis assembly from locations (C) and (D) on the right side. Protect the body pivot bores while lift the chassis.Chassis Support
1. Place supports under the front of the truck chassis. An alternate blocking point can be under the front frame and bumper. 2. Place supports under the rear of the truck chassis.785
3. To install the front strut and rear wheel assemblies only, with the strut completely retracted, 406 mm (16 in) in height is needed. Tires and rims can be installed later.4. To install the front tires and rims, 1168 mm (46 in) in height is needed.5. To install the rear tires and rims, 1118 mm (44 in) in height is needed.789
3. To install the front strut and rear wheel assemblies only, with the strut completely retracted, 457 mm (18 in) in height is needed. Tires and rims can be installed later.4. To install the front tires and rims, 1524 mm (60 in) in height is needed.5. To install the rear tires and rims, 1372 mm (54 in) in height is needed.Engine Preparation
1. Remove the engine hold down brackets from the rear of the engine, both sides. 2. Remove the bolts that fasten the front of the engine to the skid, both sides.3. The oil gauge (dipstick) and oil filler is assembled at the factory and fastened to the top of the engine for shipment. Remove the filler tube from the engine. It will be installed later