853189 Volvo.Penta Steering cable

Electrical System
Contactor Switch For Water Temperature
Water Temperature Contactor SwitchThe contactor switch for water temperature is installed in the front cover for the engine. No adjustment to the temperature range of the contactor can be made. The element feels the temperature of the coolant and then operates the micro switch in the contactor when the coolant temperature is too high. The element must be in contact with the coolant to operate correctly. If the cause for the engine being too hot is because of low coolant level or no coolant, the contactor switch will not operate.The contactor switch is connected to the fuel shutoff solenoid to stop the engine. The switch can also be connected to an alarm system. When the temperature of the coolant lowers to the operating range, the contactor switch opens automatically.Pressure Switch
Pressure SwitchThese type pressure switches are used for several purposes and are available with different specifications. They are used in the oil system and in the fuel system. One use of the switch is to open the circuit between the battery and the fuel shutoff solenoid after the oil pressure is below the pressure specifications of the switch. It also closes when the engine starts.Another use of the switch is to close and activate the battery charging circuit when the pressure is above the pressure specification of the switch. It also disconnects the circuit when the engine is stopped.Some switches of this type have three terminal connections. They are used to do two operations with one switch. They open one circuit and close another with a single switch.Electrical Indicators And Sending Units
The electrical indicators and sending units are to operate in electrical balance. Because of this, the voltage and resistance ratings are important to get the correct indications on the indicators. See Attachment Specifications to determine which indicators and sending units can be used with each other.Sending Unit And indicator For Water Temperature
Sending Unit For Water TemperatureThe position of the pointer is changed by the amount of electrical current that flows through the indicator. The water temperature is felt by the bulb of the sending unit. A change in water temperature causes a change of resistance in the sending unit. A change in resistance in the sending unit changes the current flow through the indicator and changes the position of the pointer.Sending Unit And Indicator For Oil Pressure
Oil Pressure Sending UnitThe position of the pointer is changed by the amount of electrical current that flows through the indicator. The oil pressure is felt by the sending unit for the oil pressure indicator. A change in oil pressure causes a change of resistance in the sending unit. A change in resistance in the sending unit changes the current flow through the indicator and changes the position of the pointer.Engine Protection Panel
Engine Protection Panel
(1) Oil pressure gauge. (2) Ammeter. (3) Water temperature gauge. (4) Reset button. (5) Magnetic control switch. (6) Fuse.The engine protection panel has a magnetic control switch (5) in the panel. Pushing in and holding the reset button (4), while cranking the engine, permits the engine to start. When the oil pressure is above 105 kPa (15 psi), the engine will continue to run after reset button (4) is released.
Water Temperature Contactor Switch
Pressure SwitchThe normally open contactor switch for water temperature closes when the temperature of the coolant gets higher than the setting of the switch. The oil pressure switch closes when the pressure of the oil gets lower than the setting of the switch. If either the contactor switch for water temperature or the oil pressure switch is activated, they will trip (activate) the magnetic control switch (5). This will open the circuit between the fuel shutoff solenoid and the battery. With no fuel coming to the engine, the engine will stop. A 14 ampere fuse (6) gives protection to magnetic control switch (5) if there is too much of a load put on it.Wiring Diagrams
12 Volt Starting And Charging System With Electrical Engine Protection Panel
(1) Off, Start Switch. (2) Control panel magnetic switch. (3) Water temperature sending unit. (4) Oil pressure sending unit. (5) Starter solenoid. (6) Starter motor. (7) Hourmeter. (8) Water temperature gauge. (9) Oil pressure gauge. (10) Battery. (11) Ammeter. (12) Fuel shutoff solenoid. (13) Alternator regulator. (14) Water temperature shutoff switch (normally open). (15) Oil pressure shutoff switch (normally closed). (16) Alternator.
12 Volt Starting And Charging System With Electrical Engine Protection Panel
(1) Off, Start Switch. (2) Control panel magnetic switch. (3) Water temperature sending unit. (4) Oil pressure sending unit. (5) Starter solenoid. (6) Starter motor. (7) Hourmeter. (8) Water temperature gauge. (9) Oil pressure gauge. (10) Battery (12V). (11) Ammeter. (12) Resistor diode. (13) Water temperature shutoff switch (normally open). (14) Oil pressure shutoff switch (normally closed). (15) Fuel shutoff solenoid. (16) Alternator.
Starting And Charging System
(1) Off, Start Switch. (2) Ammeter. (3) Fuel shutoff solenoid. (4) Starter solenoid. (5) Alternator regulator. (6) Starter motor. (7) Pressure switch (normally open). (8) Alternator. (9) Battery. (10) Hourmeter.
Starting And Charging System
(1) Off, Start Switch. (2) Ammeter. (3) Fuel shutoff solenoid. (4) Starter solenoid. (5) Resistor diode. (6) Starter motor. (7) Pressure switch (normally open). (8) Alternator. (9) Battery. (10) Hourmeter.
High Water Temperature And Low Oil Pressure Alarm System
(1) Water temperature contactor. (2) Oil pressure switch (normally closed). (3) Battery. (4) Toggle switch. (5) Signal light. (6) Horn. Toggle switch (4) can be in the circuit for a way to turn off horn (6).
Tachometer Wiring Diagram (One Tachometer)
(1) Tachometer. (2) Tachometer sending unit.Power Takeoff Clutches
Power Takeoff Clutches (Typical Illustration)
(1) Ring. (2) Driven discs. (3) Link assemblies. (4) Lever. (5) Key. (6) Collar assembly. (7) Nut. (8) Yoke assembly. (9) Hub. (10) Drive plates. (11) Output shaft.Power takeoff clutches (PTO's) are used to send power from the engine to accessory components. For example, a PTO can be used to drive an air compressor or a water pump.The PTO is driven by a ring (1) that has spline teeth around the inside diameter. The ring can be connected to the front or