3817048 Volvo.Penta Stud

Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.The purpose of the Special Instruction is to provide information on how to obtain the California Air Resources Board (ARB) Pre-Empt Companion label. The Special Instruction also provides information on how to install the CARB Pre-Empt Companion label to the application.
A CARB Pre-Empt Companion label is NOT an engine emissions label.
A CARB Pre-Empt Companion label is required to identify an engine application which is or is not viable for sale into the US state of California.Safety Section
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Failure to follow all safety guidelines prescribed in this document and by governing authorities and regulatory agencies may result in severe injury or death of personnel or machine damage.
Information about the CARB Pre-Empt Companion Label
The CARB Pre-Empt Companion label will be provided with the engine in the same packaging that contains any additional engine labels required by the application. The packaging includes any additional engine emission labels and is on the engine bill of material.Examples of the CARB Pre-Empt Companion Label
Illustration 1 g06438649
Typical example of label A
Illustration 2 g06438650
Typical example of label B
Illustration 3 g06438648
Typical example of label C
Note: The length of the label is 149 mm (5.866 inch). The width of the label is 52 mm (2.047 inch).Note: Label C is NOT required to be fitted to the application. Label C should be disposed off.Only label A and label B are required for installation on the application. Only one label is required to be fitted to the application.How to Obtain the CARB Pre-Empt Companion Label
The CARB Pre-Empt Companion label will be provided for each engine along with the engine emissions label.Requests for a replacement CARB Pre-Empt Companion label should be made using the "JIRA" service tool: "https://ercrequestspilotprogram.atlassian.net/servicedesk/customer/portal/2/group/19".Note: When a request is made for a replacement CARB Pre-Empt Companion label, clearly detail the engine serial number.Installation Procedure for the CARB Pre-Empt Companion Label
Where to Apply the CARB Pre-Empt Companion Label
Caterpillar recommends that a CARB Pre-Empt Companion label is installed:
An area of the application near the operator during application use.
Somewhere the operator will observe at least daily. For example, entering or exiting the cab, undertaking equipment application start-up sequence.
The CARB Pre-Empt Companion label does not need to be visible from the ground, but should be visible from a position normally encountered during normal equipment application operation. For example, entering or exiting the cab, undertaking equipment application start-up sequence, seat adjustment, sun visors.
Areas of periodic and daily maintenance are not allowed. One example would be on the bottom of the oil pan, where the label is only visible during an oil change. Another example would be behind an air cleaner housing, only visible during a filter change.
It is acceptable for the CARB Pre-Empt Companion label to be behind flexible wires, hoses, or tubes that can be easily pushed aside without being disconnected. It is acceptable to have to remove clamps to be able to read the label content.
If a person can read the majority part of the CARB Pre-Empt Companion label from a single viewing angle, and can read all parts of the label from various viewing angles, this is acceptable as long as the other criteria are met.
The CARB Pre-Empt Companion label should be in a place such that the presence of the label can be determined under normal lighting conditions, although an alternate light source might be needed to illuminate the label for reading the label.How to Apply the CARB Pre-Empt Companion Label
Adhesive films should be applied to a clean, dry, smooth surface. Adhesive films should be applied when the ambient temperature is between 15° C (59° F) and 27° C (80.6° F).Prior to installation, ensure that the surface is clean and free from contaminates, do not use acetone (propanone) to clean the area before adhering intended label surface.
Clean the surface with a 1:1 mixture of isopropyl alcohol (IPA) and water. Use a clean, lint-free paper towel to remove all dirt and contaminates from the surface.
Carefully remove the backings from the new CARB Pre-Empt Companion label. Immediately apply the label to the intended surface.Note: Avoid trapping air bubbles under the label material.
Apply pressure to the entire label to ensure adhesion.