953254 Volvo.Penta Stud


953254 Stud Volvo.Penta TD60D; TD60D-83; TD60DPP-83, TD70G; TD70G-83; TD70GPP Stud
953254 Stud Volvo Penta
Rating:
103

Buy Stud 953254 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

Volvo Penta entire parts catalog list:

TD60D; TD60D-83; TD60DPP-83; TD60DG-83; TID60D; TID60DG
TD70G; TD70G-83; TD70GPP; TD70GPP-83; TID70G; TID70GPP; TID70GG; TD70GG; TD70GG-83

Information:

Recommended Actions
Diagnostic Codes
Certain diagnostic codes may cause poor performance. Connect the Caterpillar Electronic Technician (Cat ET) and check for active codes and/or event codes. Troubleshoot any codes that are present before continuing with this procedure.Event Codes
Certain event codes may cause poor performance. Connect the Caterpillar Electronic Technician (Cat ET) and check for active codes and/or logged codes. Troubleshoot any codes that are present before continuing with this procedure.Starting Aids
Cold Mode
Use Cat ET to verify that the engine has exited Cold Mode. Cold Mode operation may slow throttle response.Air Inlet Heater (If Equipped)
Ensure that the air inlet heater is programmed to "On". Ensure that the air inlet heater is functioning properly. Refer to Troubleshooting, "Air Inlet Heater Circuit - Test" for additional information.Ether Injection System (If Equipped)
Make sure that the ether injection system is programmed to "ON". For additional information, refer to Troubleshooting, "Ether Injection System-Test".Oil Grade Plugs (If Equipped)
Ensure that the correct oil grade plug is installed. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for additional information.Active Engine Derate
Use Cat ET to check for logged engine derates and/or active engine derates. A derate status flag will appear on Cat ET if an engine derate is active. The engine may be derated due to one of the following conditions: high altitude, dirty air filters and other factors.Personality Module (Flash File)
Verify that the correct personality module (flash file) is installed.Throttle Switch
Monitor the throttle switch on Cat ET. Verify that the throttle switch is stable at the low idle position. Verify that the signal is stable at the high idle position. Move the switch from the low idle position to the high idle position in order to verify that the engine is able to reach the high idle position. Refer to Troubleshooting, "Throttle Switch Circuit - Test" for the proper troubleshooting procedure.Decelerator Pedal
Monitor the decelerator pedal on Cat ET. Verify that the decelerator pedal is operating properly. Refer to Troubleshooting, "Throttle Position Sensor Circuit - Test" for the proper troubleshooting procedure.Electrical Connectors
Check for correct installation of ECM connectors J1/P1 and J2/P2 and the unit injector connectors. Refer to Troubleshooting, "Electrical Connectors - Inspect".Unit Injectors
Use Cat ET to determine if there are any active diagnostic codes for the unit injectors.
Perform the Injector Solenoid Test on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
Perform the Cylinder Cutout Test on Cat ET in order to identify any injectors that might be misfiring. Refer to Troubleshooting, "Injector Solenoid Circuit - Test" for the proper procedure.Turbocharger Outlet Pressure Sensor
Monitor the status of "Fuel Position", "Rated Fuel Limit", and "FRC Fuel Limit" on Cat ET while the engine is operating under full load. These parameters should reflect the information below.
Table 1
"Fuel Position" = "Rated Fuel Limit"    
AND    
"Fuel Position" < "FRC Fuel Limit"    If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the electronics are operating correctly. Otherwise, proceed with the next Step.
Monitor the status of "Boost Pressure" and "Atmospheric Pressure" for normal operation on Cat ET. When the engine is not running, "Boost Pressure" should be 0 kPa (0 psi).Air Inlet and Exhaust System
Observe the Check Engine Lamp. Check for an air filter restriction indicator. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Testing and Adjusting, "Air Inlet and Exhaust System".Fuel Supply
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for foreign objects which may block the fuel supply.
Check for air in the low pressure fuel supply system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Testing and Adjusting for more information.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Purge air from the low pressure fuel supply circuit. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.
Check fuel quality. In temperatures below 0 °C (32 °F), check for solidified fuel (wax). Refer to Special Instruction, SEBD0717, "Diesel Fuels And Your Engine".
Check the fuel pressure after the fuel filter while the engine is being cranked. Refer to Testing and Adjusting for the correct pressure values. If the fuel pressure is low, replace the fuel filters. If the fuel pressure is still low, check the following items: fuel transfer pump, fuel transfer pump coupling and fuel pressure regulating valve. Refer to Testing and Adjusting for more information.


Parts stud Volvo Penta:

244380
Stud
244380 Stud
AQD70D; TAMD70D; TAMD70E, D70CHC; D70CRC; TD70CHC, MD120A; MD120AK; TMD120A, MD70C; TMD70C; TAMD70C, TAD1030G; TD1010G; TWD1010G, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAMD61A; TAMD62A, TAMD71A; TAMD72A, TD100CHC; TD100CRC; TD1
130673
Stud
130673 Stud
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAD
953224
 
953224 Stud
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAD
241771
Stud
241771 Stud
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TAMD61A; TAMD62A, TAMD71A; TAMD72A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TD1
953486
 
953486 Stud
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D42A; D42A PP, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, DH10A; DH10A 285; DH10A 360, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B;
244501
Stud
244501 Stud
TAMD60A; TAMD60B, TD60A; TD60B; TD60B PP, TD60D; TD60D-83; TD60DPP-83
848217
 
848217 Stud
TAMD63L-A; TAMD63P-A, TAMD71B; TAMD73P-A; TAMD73WJ-A, TD60D; TD60D-83; TD60DPP-83, TD61A; TD61AW; TD61ACE
7743120_075
 
7743120_075 STUD
TD60D; TD60D-83; TD60DPP-83
Back to top