848864 Volvo.Penta Suction pipe

start by:a) remove crankshaft pulleyb) remove alternatorc) remove oil pan 1. Disconnect wires (1) from the air conditioner compressor.2. Remove bolt (3), the washer and spacer from the belt adjuster. Remove two bolts (2) and move the air conditioner compressor clear of the timing gear cover. 3. Disconnect wire (4) from the temperature switch and remove the clip that holds the wire harness to the timing gear cover.4. Disconnect water temperature thermocouple (6) from the timing gear cover.5. Disconnect heater hoses (5) and (9) from the timing gear cover.6. Remove alternator bracket (7).7. Remove tachometer drive housing (8) from the timing gear cover.8. Close the fuel shutoff valve on the back side of the water separator fastened to the hydraulic tank. 9. Remove bolt (10) and the clamp from the fuel lines. Disconnect fuel lines (11) from the fuel filter base. Remove the fuel filter base and bracket as a unit from the timing gear cover.10. Remove clamp (12) from the water sleeve in each cylinder head. 11. Remove panel (13). 12. Use tool (A) and a screwdriver to push water sleeves (14) into the timing gear cover. 13. Remove bolts (15) and spacers from the engine front support. 14. Remove suction tube (16) from the oil pump.15. Remove only the 1/2 in. bolts from the guard below the pump drive and turn the guard out of the way. 16. Loosen bolts (17) that hold the pump drive to the frame. 17. Remove water connector (18) and water elbow (19) from the timing gear cover.18. Fasten tooling (B) and a hoist to the timing gear cover. Lift the front of the engine just enough to install tooling (C) under the cylinder block. Lower the engine on to tooling (C) so the tooling holds the weight of the engine not engine support (20). Remove engine support (20) from the timing gear cover.19. Put identification on the bolts that hold the timing gear cover to the cylinder block so they will be installed in the correct location. Remove the bolts from the timing gear cover.
Be extra careful not to damage the crankshaft front seal during removal and installation of the timing gear cover.
20. Remove timing gear cover (21) and the oil pump from the dowels on the cylinder block. The weight of the timing gear cover and oil pump is 62 kg (136 lb.).Install Timing Gear Cover And Oil Pump
1. Clean the contact surfaces of the cylinder block and timing gear cover. Install the timing gear cover gasket on the cylinder block. Cut the gasket even with the bottom face of the cylinder block. Put 5H2471 Gasket Cement on the bottom of the gasket where the gasket makes contact with the gasket for the oil pan. Make sure the water sleeves are installed in the timing gear cover. Put oil on the seals. 2. Fasten tooling (B) and a hoist to the timing gear cover and put the timing gear cover in position on the engine. Make sure seal (1) is not damaged and the oil pump gear and crankshaft gear are in alignment. Install the bolts that hold the cover in place. 3. Install engine support (4) on the timing gear cover. Lift the front of the engine and remove tooling (C) from under the cylinder block. Lower the engine back on to support (4).4. Install water connector (2) and elbow (3) on the timing gear cover. 5. Install bolts (5), the washers, spacers and nuts that hold the engine front support to the frame. Tighten bolts (5) to a torque of 122 20 N m (91 15 lb.ft.). 6. Tighten bolts (6) that hold the pump drive to the frame to a torque of 427 67 N m (311 49 lb.ft.). Put the guard in position below the pump drive and install the bolts that hold it in place. 7. Install suction tube (7) on the oil pump. 8. Use tool (A) and a screwdriver to push the water sleeve into both cylinder heads. 9. Install clamps (8) on the water sleeves. 10. Install panel (9) on the right side of the engine. 11. Install the fuel filter base and bracket on the timing gear cover. Connect fuel lines (10) to the fuel filter base and install clamp (11) on the fuel lines.12. Open the fuel shutoff valve on the back side of the water separator fastened to the hydraulic tank. 13. Connect wire (12) to the temperature switch and install the clip that holds the wire to the timing gear cover.14. Connect water temperature thermocouple (13) to the timing gear cover. 15. Put clean oil on the seals in tachometer drive housing (14) and install the the housing on the timing gear cover.16. Connect heater hoses (15) and (17) to the timing gear cover.17. Install alternator bracket (16). 18. Put air conditioner compressor (18) in position on the mounting bracket and install the bolts that hold it in place. Install the bolt, washer and spacer in belt adjuster (19) on the compressor. Connect the wires to the compressor.end by:a) install oil panb) install alternatorc) install crankshaft pulley