21248914 Volvo.Penta Tank


21248914 Tank Volvo.Penta TAD1640GE; TAD1641GE; TAD1642GE Tank
21248914 Tank Volvo Penta
Rating:
28

Buy Tank 21248914 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Compatible models:

Volvo Penta entire parts catalog list:

TAD1640GE; TAD1641GE; TAD1642GE; TAD1650GE; TAD1651GE; TWD1643GE; TWD1652GE; TWD1653GE; TWD1663GE

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
B(1) 9U-6198 Crankshaft Turning Tool 1
B(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure.
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove" for the correct procedure.Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Plug the apertures for the push rods and injector sleeves in the cylinder head to prevent the entry of loose parts into the engine.
Rotate the crankshaft to position the piston of the cylinder that is being worked on in the top dead center position.
Illustration 1 g06361900
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Follow Step 2a through Step 2d to position the appropriate piston at top dead center.
Install Tooling (A) in position on the cylinder head to compress a valve spring (10) for the appropriate piston.
Use Tooling (A) to compress valve spring (10) and open the valve slightly.Note: Do not compress the spring so that valve spring retainer (9) touches valve stem seal (11).
Use Tooling (B) to rotate the crankshaft carefully, until the piston touches the valve.Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top dead center position. The valve is now held in a position that allows the valve spring to be safely removed.Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of each cylinder. If all valve springs require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that all of the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Do not turn the crankshaft while the valve springs are removed.
Apply sufficient pressure to Tooling (A) to allow removal of valve keepers (1).Note: Do not compress the spring so that valve spring retainer (2) touches valve stem seal (4).Remove valve keepers (1).
Slowly release pressure on Tooling (A).
Remove valve spring retainer (2) and remove valve spring (10).
If necessary, remove valve stem seals (4).
Repeat Step 3 through Step 6 to remove the remaining valve springs from the appropriate cylinder.
Remove Tooling (A).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-6193 Valve Spring Compressor 1
416-0288 Adapter 1
416-0292 Head 1
B(1) 9U-6198 Crankshaft Turning Tool 1
B


Parts tank Volvo Penta:

21643134
 
21643134 Tank
TAD1640GE; TAD1641GE; TAD1642GE, TWD1672GE; TWD1673GE; TWD1672-1673GE
22663471
 
22663471 Tank
TAD1640GE; TAD1641GE; TAD1642GE, TWD1672GE; TWD1673GE; TWD1672-1673GE
22347419
 
22347419 Tank
TAD1640GE; TAD1641GE; TAD1642GE, TWD1672GE; TWD1673GE; TWD1672-1673GE
21249001
 
21249001 Tank
TAD1640GE; TAD1641GE; TAD1642GE
21248998
 
21248998 Tank
TAD1640GE; TAD1641GE; TAD1642GE
21248967
 
21248967 Tank
TAD1640GE; TAD1641GE; TAD1642GE
21248975
 
21248975 Tank
TAD1640GE; TAD1641GE; TAD1642GE
21248929
 
21248929 Tank
TAD1640GE; TAD1641GE; TAD1642GE
Back to top