861664 Volvo.Penta Tensioning arm


861664 Tensioning arm Volvo.Penta KAD32P; TAMD42WJ-A; KAD43P-A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A Tensioning
861664 Tensioning arm Volvo Penta
Rating:
63

Buy Tensioning arm 861664 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$10.54

22-10-2024

US: Vinnikshop
for Porter Cable Replacement Washer, 861664
DANGER CLOSE TACTICAL TRAINING For Porter Cable Replacement Washer, 861664 || replacement washer desied for Porter Cable power too, part number 861664. || Eres proper fit and sealing to prevent leaks, cpatible with specific Porter Cable mode. || To ensure the best fit and make a well-informed decision, please carefully check the product dimensions and review the provided images || To ensure a perfect fit and make an informed decision, we encourage you to carefully review both the product's dimensions and visually inspect it in the provided photos.
$10.54

22-10-2024

US: Tsirukstore
for Porter Cable Replacement Washer, 861664
EMROZE AS IF THERE WERE NO TOMORROW For Porter Cable Replacement Washer, 861664 || replacement washer for Porter Cable power too, eres a secure fit and proper sealing. || Part number 861664, desied for use with specific Porter Cable mode, construction for durability. || Enhance your lawn care routine! Maintain your mower’s peak performance with our high-quality parts. Check dimensions and photos for accurate compatibility. || For a precise fit and wise selection, make sure to thoroughly check the product’s dimensions and review the accompanying photos.
$12.19

22-10-2024

US: Tsirukstore
for Porter Cable 2 Pack of Replacement Washers, 861664-2PK
EMROZE AS IF THERE WERE NO TOMORROW For Porter Cable 2 Pack Of Replacement Washers, 861664-2PK || replacement washers for Porter Cable too, desied for reliable perforce. || Pack includes 2 washers with MPN 861664, ering a proper fit for your equipment. || Enhance your lawn care routine! Maintain your mower’s peak performance with our high-quality parts. Check dimensions and photos for accurate compatibility. || For a precise fit and wise selection, make sure to thoroughly check the product’s dimensions and review the accompanying photos.
Number on catalog scheme: 29
 

Volvo Penta entire parts catalog list:

KAD32P; TAMD42WJ-A; KAD43P-A; KAMD43P; KAMD43P-A; KAMD43P-B; KAD44P; KAD44P-B; KAD44P-C; KAMD44P-A; KAMD44P-C; KAD300-A; KAMD300-A; HS1A; HS1E
KAD42B; KAMD42B; TAMD42B
KAD42P-A; KAMD42P-A; HS1A

Information:


Illustration 1 g06151593
Schematic of the diagnostic connector and the data link connector for a diagnostic connector that is mounted off engine
Illustration 2 g06151589
Schematic of the diagnostic connector and the data link connector for an engine-mounted diagnostic connector
Illustration 3 g02028056
P1 pin locations for the diagnostic connector
(8) Data link +
(9) Data link -
Illustration 4 g02090413
Typical view of the P2 pin locations for the diagnostic connector
(20) Data link +
(28) Data link -
(53) Voltage supply (diagnostic connector)
(54) Return (diagnostic connector)Complete the procedure in the order in which the steps are listed.
Table 1
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Turn the keyswitch to the OFF position.
B. Inspect the connectors in the circuit for the data link.
Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
D. Check the screw for the P1 and P2 ECM connectors for correct torque of 6 N m (53 lb in).
E. Check all the wiring associated with the data link for abrasions and pinch points.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: A damaged wire or damaged connector was not found.
Proceed to Test Step 2.
2. Determine the Type of Fault in the Data Link
A. Connect the electronic service tool to the diagnostic connector that is on the engine harness or on the application.
Repair: Turn the keyswitch to the ON position.
Power to the comms adapter
Result: The power lamp illuminates on the communications adapter. The communications adapter is receiving the correct voltage.
Proceed to Test Step 5.
Result: The power lamp is not illuminated on the communications adapter. The communications adapter is not currently receiving the correct voltage.
Proceed to Test Step 3.
3. Check the Battery Voltage at the Diagnostic Connector
A. Turn the keyswitch to the ON position.
B. Use a multimeter to measure the voltage from pin A (battery+) and pin B (ground) of the diagnostic connector.
11.0 VDC and 13.5 VDC for a 12 VDC system. 22.0 VDC and 27.0 VDC for a 24 VDC system.
Result: The voltage is between 22.0 VDC and 27.0 VDC for a 24 V system. The voltage is between 11.0 VDC and 13.5 VDC for a 12 V system. The diagnostic connector is receiving the correct voltage.
Proceed to Test Step 5.
Result: The voltage is not between 22.0 VDC and 27.0 VDC for a 24 V system. The voltage is not between 11.0 VDC and 13.5 VDC for a 12 V system. The diagnostic connector is not currently receiving the correct voltage.
Proceed to Test Step 4.
Illustration 5 g03705906
Typical view of the diagnostic connector from the wire side
(A) Switched battery +
(B) Battery ground (GND)
(D) Data link +
(E) Data link -
Table 2
Troubleshooting Test Steps Values Results
4. Bypass the Wiring for the Diagnostic Connector
A. Disconnect the wires from pin A and pin B of the diagnostic connector.
Note: If the diagnostic connector is mounted on the engine, perform Steps B to D. If the diagnostic connector is mounted off the engine, perform Step E.
B. Disconnect the wires from P2:53 and P2:54.
C. Fabricate a jumper wire to connect pin A of the diagnostic connector to P2:53.
D. Fabricate a jumper wire to connect pin B of the diagnostic connector to P2:54.
E. Fabricate a jumper wire to connect pin "A" of the diagnostic connector to battery+ and pin "B" to the battery-.
F. Connect the electronic service tool to the diagnostic connector that is on the engine harness or on the application.
G. Turn the keyswitch to the ON position. The power lamp should illuminate on the communications adapter.
Other devices are OK
Result: The power lamp is illuminated. The fault is in the harness.
Repair: Repair the faulty harness or replace the faulty harness.
Use the electronic service tool to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The power lamp is not illuminated.
Proceed to Test Step 6.
5. Check the Data Link Connections
A. Turn the keyswitch to the OFF position.
B. Disconnect the communications adapter from the diagnostic connector.
C. If the diagnostic connector is installed on the application, disconnect connector P1 from the ECM. Check the resistance between P1:8 and pin "D" on the diagnostic connector. Check the resistance between


Parts tensioning Volvo Penta:

861660
 
861660 Tensioning arm
KAD32P; TAMD42WJ-A; KAD43P-A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, MD2010-C; MD2010-D; MD2020-C, MD2010B; MD2020B; MD2030B
861667
 
861667 Tensioning arm
KAD32P; TAMD42WJ-A; KAD43P-A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A
860835
 
860835 Tensioning arm
KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B
860928
 
860928 Tensioning screw
KAD42B; KAMD42B; TAMD42B
860962
 
860962 Tensioning arm
KAD42B; KAMD42B; TAMD42B
Back to top