855411 Volvo.Penta Thermostat housing

Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     138-7575     Link Bracket     2    Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Remove the hood assembly. Refer to Disassembly and Assembly, "Hood - Remove".
Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "System Pressure - Release".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand.Remove the fill cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the cooling system. The capacity of the cooling system is 81 L (21 US gal). Refer to Operation and Maintenance Manual, SEBU7362, "980G Series II Wheel Loader", "Cooling System Coolant (ELC) - Change".
Personal injury can result from contact with refrigerant.Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.
Evacuate the air conditioner refrigerant from the air conditioning system. Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.
Illustration 1 g00513547
Support lower counterweight (1) with a suitable lift truck, as shown.
Remove six bolts (2) and remove lower counterweight (1). The weight of the lower counterweight is 1032 kg (2275 lb).
Illustration 2 g00800376
Disconnect two hydraulic hoses (4) from hydraulic oil cooler (3) .
Illustration 3 g00800378
Illustration 4 g00800684
Remove two hose clamps (7) which hold hose assembly (5) in place.
Remove the two bolts which hold bracket (10) in place. Remove bracket (10) .
Disconnect two hose assemblies (5) and (9) from refrigerant condenser (6) .
Remove hose clamp (8) which holds the two hose assemblies in place.
Illustration 5 g00800481
Loosen clamps (11) which secure tube assembly (12) in place. Remove tube assembly (12) from the radiator