785606 Volvo.Penta Tube


785606 Tube Volvo.Penta D120A; D120AK; TD120A Tube
785606 Tube Volvo Penta
Rating:
28

Buy Tube 785606 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$152.13
 

01-09-2017
1.80[0.45] pounds
A1 Cardone: A1 Cardone
Cardone 78-5606 Remanufactured Ford Computer
On-car vehicle validation testing ensures product fits and functions properly||OE components with high failure rates are 100% replaced||All electronic modules are 100% tested to ensure they meet OE requirements for the application||Advanced robotic equipment ensures precision made units and consistent high quality with every part||Every unit is 100% tested to ensure quality and reliability
$627.79
 

06-07-2022
18.5[8.10] Pounds
-: -
APDTY 785606 Integrated Manifold Includes All Gaskets; Tubular
Meets Or Exceeds OEM Specs || Factory OEM Fit Form And Function
Number on catalog scheme: 27
 

Compatible models:

Volvo Penta entire parts catalog list:

D120A; D120AK; TD120A; TD120AG; TD120AG PP; TD120AK

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     6V-6640     Sealant     1    
B     -     Guide Bolt
M8 by 40 mm     2    
C     319-6486     Alignment Tool     1    
- Bolts
M10 by 50 mm     3    
D     1U-6396     O-Ring Assembly Compound     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Ensure that the front housing is clean and free from damage. If necessary, replace the front housing.If necessary, install blanking plugs to a new front housing. Use Tooling (A) in order to seal all D-plugs.
Clean all the gasket surfaces of the cylinder block.
Illustration 1 g02198913
Illustration 2 g02198914
Inspect dowel (12) and dowel (13) for damage. If necessary, replace the dowels in the cylinder block.
Install thrust washer (11) into the recess in the cylinder block. Refer to Disassembly and Assembly, "Camshaft - Install" for more information.
Install Tooling (B) to the cylinder block. Refer to Illustration 2.
Align a new gasket (10) with Tooling (B) . Install the gasket to the cylinder block.Note: Ensure that two circular Tabs (X) on the gasket are engaged in two Holes (Y) in the cylinder block. Ensure that dowel (12) in the cylinder block is engaged on the gasket.
Install Tooling (C) to the cylinder block.
Install the front housing over Tooling (B) and Tooling (C) onto the cylinder block.
Illustration 3 g02198915
(7) M8 by 20 mm (8) M8 by 35 mm (9) M8 by 25 mm
Install new bolts (9) to front housing (4) hand tight.
Remove Tooling (B) .
Loosely install bolts (7) and bolts (8) finger tight. Refer to Illustration 3 for the correct position of the bolts.
Illustration 4 g01998054
Tighten bolts (7) , bolts (8) and bolts (9) in the sequence that is shown in Illustration 4 to a torque of 28 N m (248 lb in).
Remove Tooling (C) from the cylinder block.
Illustration 5 g02198874
Install new O-ring seal (5) and O-ring seal (6) to bypass tube (1) . Use Tooling (D) in order to lubricate the O-ring seals.
Install bypass tube (1) to the cylinder head. Install bolts (3) . Tighten the bolts to a torque of 9 N m (80 lb in)
Install a new cable strap (2) to the wiring harness assembly.End By:
Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install" for the correct procedure.
Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install" for the correct procedure.
If the engine has an accessory drive, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
Install the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove" for the correct procedure.
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Install" for the correct procedure.
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install" for the correct procedure.
Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Fill" for the correct procedure.


Parts tube Volvo Penta:

822558
 
822558 Tube
D120A; D120AK; TD120A, MD120A; MD120AK; TMD120A
822559
Tube
822559 Tube
D120A; D120AK; TD120A, MD120A; MD120AK; TMD120A
822560
Tube
822560 Tube
D120A; D120AK; TD120A, MD120A; MD120AK; TMD120A
822561
Tube
822561 Tube
D120A; D120AK; TD120A, MD120A; MD120AK; TMD120A
467090
 
467090 Tube
D100A; D100AK; D100B, D120A; D120AK; TD120A, TAD1030P, TD100G-87; TD1030ME; TWD1030ME, TD100G; TD100G-85; TD100G-87, TID120FPP; TID120FG; TD120G
423347
Tube
423347 Tube
D120A; D120AK; TD120A
423348
Tube
423348 Tube
D120A; D120AK; TD120A
423349
Tube
423349 Tube
D120A; D120AK; TD120A
Back to top