840846 Volvo.Penta Tube

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines.Dispose of fluids according to local regulations and mandates.
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact skin.At operating temperature, the engine coolant is hot and under pressure.Steam can cause personal injury.Check the coolant level only after the engine has been stopped and the cooling system pressure cap is cool enough to touch with your bare hand.Remove the cooling system pressure cap slowly to relieve pressure.Cooling system conditioner contains alkali. Avoid contact with the skin and eyes to prevent personal injury.
Personal injury can result from contact with refrigerant.Contact with refrigerant can cause frost bite. Keep face and hands away to help prevent injury.Protective goggles must always be worn when refrigerant lines are opened, even if the gauges indicate the system is empty of refrigerant.Always use precaution when a fitting is removed. Slowly loosen the fitting. If the system is still under pressure, release it slowly in a well ventilated area.Personal injury or death can result from inhaling refrigerant through a lit cigarette.Inhaling air conditioner refrigerant gas through a lit cigarette or other smoking method or inhaling fumes released from a flame contacting air conditioner refrigerant gas, can cause bodily harm or death.Do not smoke when servicing air conditioners or wherever refrigerant gas may be present.Use a certified recovery and recycling cart to properly remove the refrigerant from the air conditioning system.
Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This will help prevent fluid loss and this will help to prevent contaminants from entering the system. 1. Remove four bolts (1), the nuts and the washers that hold crossbeam (2) to the rear frame. Remove crossbeam (2). The weight of the crossbeam is 24 kg (53 lb). 2. Remove two hose clips (3) from the torque converter updrive transfer gearbox. 3. Remove hose clip (5) from the torque converter outlet relief valve. Move hose assembly (4) away from the torque converter updrive transfer gearbox. 4. Disconnect electrical connectors (6) and (7) (if equipped). Remove bolt (8) to disconnect the earth wire to the wiring harness.5. Remove cable strap (9) from the harness clip.6. Disconnect hose assembly (10) from the torque converter outlet relief valve. 7. Loosen the hose clamp and disconnect hose (11) (if equipped).8. Loosen the hose clamp and disconnect tube assembly (12). 9. Loosen the two hose clamps and remove hose and tube assembly (13). 10. Loosen the two hose clamps and remove hose and tube assembly (14).11. Loosen the hose clamp and remove hose and tube assembly (15). 12. Remove the nut, the washer and the harness clip from the engine side of stud (16). 13. Disconnect electrical connector (17).14. Remove two harness clips (18).15. Disconnect the engine speed sensor harness from electrical connector (19).16. Remove cable strap (20) from the harness clip. 17. Remove three cable straps (21). 18. Remove nut (23) and the washer from the start relay. Disconnect cable (22).19. Move cable (22) forward, away from the engine. 20. Remove three harness clips (24).21. Remove bolt (25) to disconnect the earth wire to the wiring harness.22. Remove bolts (26), (27) and the washers that hold the axle oil cooling hose assemblies (if equipped) to bracket (28). 23. Remove hose clip (29) and harness clip (31).24. Disconnect hose assembly (30) from the torque converter updrive transfer gearbox. 25. Disconnect hose assembly (32) from the torque converter updrive transfer gearbox.26. Loosen the two hose clamps and disconnect hose assembly (33) from the torque converter updrive transfer gearbox. 27. Disconnect hose assemblies (34) and (35).28. Disconnect hose assembly (36) (if equipped) and hose assembly (37). 29. Loosen the hose clamp and disconnect hose (38) (if equipped).30. Remove hose clip (39), two hose clips (40), two hose clips (41) and hose clip and bracket (42) (if equipped). Move the hoses away from the engine. 31. Disconnect cables (43), (44) and (45) from the starter.32. Disconnect electrical connector (46). 33. Disconnect electrical connector (47). 34. Disconnect hose assembly (48). 35. Remove bolt (49), the washer, the spacer and the two clamp assemblies. 36. Disconnect hose assembly (50) from the transmission oil cooler.37. Remove bolt (51), the washer, the spacer and the clamp assembly. 38. Disconnect tube assembly (52) from the main implement pump. 39. Disconnect electrical connector (53) and electrical connector (54) (if equipped). It is necessary to recover the air conditioner refrigerant from the air conditioner system before disconnecting hose assemblies (55) and (56). Refer to Service Manual, SENR5664,