847032 Volvo.Penta Tube


847032 Tube Volvo.Penta TAMD103A, TMD100C, TMD102A; TAMD102A; TAMD102D Tube
847032 Tube Volvo Penta
Rating:
53

Buy Tube 847032 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$14.90
 

13-05-2022
1.43[0.45] Pounds
-: -
Genius Tools 1" Dr. 32mm Impact Socket (CR-Mo) - 847032
IMPACT SOCKET - 32mm 6-point Impact Socket || SPECIFICATIONS - 1 Inch Drive Size with an overall length of 63mm (or 2.48 Inches) || DURABLE MATERIALS - Made from Chrome Moly Steel for high strength and durability while having anti-corrosive properties || TOOL ORGANIZATION - Sizes are stamped for permanent and easy identification of size || SUPERIOR DESIGN - Heat treated through oil quenching with a matte black oxide coating which creates a tough, durable exterior and superior inner core strength for a lifetime of professional use || PEACE OF MIND - Purchase with confidence backed by the Genius Tools Limited Lifetime Warranty against manufacturer defects || ANSI STANDARDS - Meets or exceeds the standards established by the American National Standards Institute || PROFESSIONAL GRADE - Genius Tools are designed and made for use by professional technicians and built to perform over a lifetime of heavy use. Trust Genius for a quality tool at a value cost to you
$82.86
 

30-08-2017

BRIGHTON-B: BRIGHTON-BEST
BBI 847032 Cap Screw, 1/4-20 UNC x 5 in, 7/16 in Hex Drive, Grade 5, (BOX OF 400)
Number on catalog scheme: 34
 

Compatible models:

Volvo Penta entire parts catalog list:

Information:

Start By:a. remove valve covers Call out (1) and (2) are not used in this removal procedure. Call outs begin with number (3). 1. Remove bolts (3) that hold the valve cover bases to the cylinder head assembly. Remove valve cover bases (4).
To prevent damage to the fuel injection nozzle, hold adapter assembly (5) in position at the of injection nozzle (6) when fuel line nut (7) is loosened or tightened.
2. Use Tool (A) and a 7/8 5P0328 Crow Foot ( in) to loosen the fuel injection line nut at the nozzle end. 3. Use Tool (B) to loosen the nut at the fuel injection line adapter end. Remove inner fuel injection lines (8). Install caps and plugs on all fuel injection line openings to keep dirt out of the fuel system. 4. Remove bolts (9) that hold the rocker shaft assemblies to the cylinder head assembly.5. Remove rocker shaft assemblies (10). 6. Put identification marks on the push rods as to their location in the engine. Remove push rods (11). 7. Put identification marks on the bridges as to their location in the engine. Remove bridges (12) from the dowels on the cylinder head assembly.Install Rocker Shaft Assemblies & Push Rods
1. Put clean engine oil on the bridges and dowels. Install the original bridges in their respective locations. New bridges can be mixed.2. Install bridges (1) on the bridge dowels. While firmly pressing 0.5 to 4.5 kg (1 to 10 lb) straight down on the top contact surface of the bridge, turn the adjusting screw clockwise until contact is made with the valve stem. Turn the screw an additional 1/31/2 20 to 30 degrees ( to of 1 hex on nut). This will straighten the dowel in the guide and compensate for the slack in the threads. Hold the adjusting screw in this position and tighten the locknut to a torque of 30 4 N m (22 3 lb ft). Install the original push rods in their respective locations in the engine. New push rods can be mixed.3. Install push rods (2). 4. Put rocker shaft assemblies (3) in position on the cylinder head assembly.5. Put clean engine oil on the threads of the bolts that hold the rocker shaft assemblies in place. Tighten the bolts first to a torque of 270 25 N m (200 18 lb ft). Start with the bolt in the center of the rocker shaft assembly. Tighten the bolts again to a torque of 450 20 N m (330 15 lb ft). Tighten the bolts again by hand to a torque of 450 20 N m (330 15 lb ft).
Do not cause damage to the O-ring seals on the inner fuel lines.
6. Install inner fuel injection lines (4). Tighten the fuel injection line adapter nuts (5) to a torque 40 7 N m (30 5 lb ft) with Tool (A).
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turns in the body.
7. Tighten fuel injection line nut (6) to a torque of 40 7 N m (30 5 lb ft) with Tool (B) and a 7/8 5P0328 ( in) Crow Foot wrench.8. Make adjustments to the valves until the intake valve clearance is 0.38 mm (.015 in) and the exhaust valve clearance 0.76 mm (.030 in). See the topic "Valve Clearance Setting" in Testing & Adjusting Manual SENR6471. Tighten the locknut to a torque of 30 4 N m (22 3 lb ft) and check the adjustments. 9. Install valve cover bases (7) on the cylinder head assembly. Install bolts that hold the valve cover bases in place. Tighten the bolts to a torque of 14 3 N m (10 2 lb ft).End By:a. install valve covers


Parts tube Volvo Penta:

845645
 
845645 Tube
AQD70D; TAMD70D; TAMD70E, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70C; TMD70C; TAMD70C, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TMD100C, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
842831
 
842831 Tube
MD120A; MD120AK; TMD120A, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TD100CHC; TD100CRC; TD121CHC, TD120AHC; TD120ARC; TAD120AHC, TMD100C, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
422751
Tube
422751 Tube
TAMD103A, TMD102A; TAMD102A; TAMD102D
848983
Tube
848983 Tube
TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TAMD162A; TAMD162B; TAMD162C, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
863555
 
863555 Tube
TAMD103A, TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P
3826852
 
3826852 Tube
TAMD103A
846707
 
846707 Tube, reverseing gear
TD100CHC; TD100CRC; TD121CHC, TMD102A; TAMD102A; TAMD102D
864303
Tube, intercooler
864303 Tube, intercooler
TMD102A; TAMD102A; TAMD102D
Back to top