7743460_054 Volvo.Penta upper gear unit


7743460_054 upper gear unit Volvo.Penta AQ231A; AQ231B; AQ231LB upper
7743460_054 upper gear unit Volvo Penta
Rating:
53

Buy upper gear unit 7743460_054 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

Compatible models:

Volvo Penta entire parts catalog list:

AQ231A; AQ231B; AQ231LB; 290A; DP-A; SP-A; 275A; 285A

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     370-8376     Cap Kit     1    
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Remove the inlet air control (NRS Induction Mixer) and mounting bracket.
Remove the crankcase breather cannister and tube assemblies.
Illustration 1 g02177626
Cut cable straps (6) from the wiring harness assemblies.
Slide the locking tab for wiring harness connection (2) into the unlocked position. Remove wiring harness connection (2) from the pressure sensor.
Slide the locking tab for wiring harness connection (3) into the unlocked position. Remove wiring harness connection (3) from the pressure sensor.
Slide wiring harness connection (7) from the mounting bracket and position harness away from the inlet elbow.
Remove bolt (4) and bolt (8) from clips for tube assemblies.
Remove bolts (5) and remove manifold (1) from the inlet elbow.
Illustration 2 g02358237
Remove bolts (9) and remove inlet elbow (10) from the cylinder head.
Remove gasket (11) .
Illustration 3 g02177628
Loosen bolt (22) and bolt (24) for tube clamp (13) support bracket.
Remove bolt (14) from tube clamp (13). Remove the tube clamp from fuel injection lines (12). Remove rubber separator (25) .
Use a suitable tool in order to remove tube clamp (15) from fuel injection lines (12) .
Loosen bolt (23) for tube clamp (17) .
Remove bolt (18) from tube clamp (17). Remove tube clamp (17) from fuel injection lines (19). Remove rubber separator (26) .
Clean the area around the nuts for fuel injection lines (12) and fuel injection lines (12). Ensure that the area is free from contamination before beginning disassembly.
Disconnect fuel injection line (12) from the electronic unit injector.
Disconnect fuel injection line (12) from fuel manifold (16) .
Use Tooling (A) in order to plug the open port in the electronic unit injector immediately.
Remove fuel injection line (12). Discard the fuel injection lines.
Use Tooling (A) in order to plug the open port in fuel manifold (16) immediately.
Remove seal (20) from the electronic unit injector and cylinder head (21) .
Repeat Step 19 through Step 25 in order to remove the remaining fuel injection lines from the fuel manifold to the electronic unit injectors.
Illustration 4 g02177629
Remove bolt (24) and bolt (25) from tube clip for fuel injection line (22) .
Disconnect fuel injection line (22) from fuel injection pump (23) .
Disconnect fuel injection line (22) at fuel manifold (16) .
Remove fuel injection line (22). Discard the fuel injection lines.
Use Tooling (A) in order to plug all open ports immediately in fuel manifold (16) and in fuel injection pump (23) .


Parts upper Volvo Penta:

839403
 
839403 Upper section
230A; 230B; 250A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ23
853070
Upper gear
853070 Upper gear
AQ125B, AQ131A; AQ131B; AQ131C, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ200D; AQ200F; 280B, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C, AQ311A; AQ311B, MD31A; TMD31A; TMD31B,
854022
Upper gear
854022 Upper gear
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, AQ131A; AQ131B; AQ131C, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ231A; AQ231B; AQ231LB, AQ271A; AQ271B; AQ271C, AQ311A; AQ311B, MD31A; TMD31A; TMD31
3803114
 
3803114 Upper gear, exch
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, AQ131A; AQ131B; AQ131C, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ231A; AQ231B; AQ231LB, AQ271A; AQ271B; AQ271C, AQ311A; AQ311B, MD31A; TMD31A; TMD31
7743460_040
 
7743460_040 upper gear unit
AQ231A; AQ231B; AQ231LB
7743460_041
 
7743460_041 upper gear unit
AQ231A; AQ231B; AQ231LB
7743460_049
 
7743460_049 upper gear unit
AQ231A; AQ231B; AQ231LB
7743460_061
 
7743460_061 upper gear unit
AQ231A; AQ231B; AQ231LB
Back to top