3580305 Valve stem seal Volvo.Penta
D1-13; D1-13B; D1-20, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
Valve
Price: query
Rating:
Number on catalog scheme: 2
Compatible models:
Volvo Penta entire parts catalog list:
- Cylinder Head » 3580305
- Cylinder Head
D2-75; D2-75B; D2-75C; D2-60F; D2-75F
MD2010-C; MD2010-D; MD2020-C; MD2020-D; MD2030-C; MD2030-D; MD2040-C; MD2040-D; 120S-D; 120S-E
MD2010A; MD2020A; MD2030A; MD2040A; MS2B-R; MS2A-D; MS2A-E; MS2L-D; MS2L-E; 120S-D; 120S-E; MD2010; MD2030; MD2040; MD2020
MD2010B; MD2020B; MD2030B; MD2040B; MS2L-D; MS2A-D; 120S-D; MS2B-R; MS2A-E; MS2L-E
Information:
Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
105-3 Inlet Manifold Temperature Sensor voltage above normal The engine's Electronic Control Module (ECM) detects signal voltage that is more than 4.8 VDC for one second.
The ECM has been powered for at least three seconds. The code is logged.
The value of the parameter is set to zero.
105-4 Inlet Manifold Temperature Sensor voltage below normal The ECM detects signal voltage that is less than 0.2 VDC for one second.
The ECM has been powered for at least three seconds.
175-3 Engine Oil Temperature Sensor voltage above normal The ECM detects signal voltage that is more than 4.8 VDC for one second.
The ECM has been powered for at least three seconds. The code is logged.
The value of the parameter is set to zero.
175-4 Engine Oil Temperature Sensor voltage below normal The ECM detects signal voltage that is less than 0.2 VDC for one second.
The ECM has been powered for at least three seconds. System OperationUse this procedure to troubleshoot any suspect problems with the following sensors:
Inlet manifold temperature sensor
Engine oil temperature sensorThe sensor signal for the passive sensors is routed from the ECM to the connector for the right rail. The sensor signal is then routed to terminal 1 of each sensor connector. The sensor return for the passive sensors is routed from the ECM to the connector for the right rail. The sensor return is then routed to terminal 2 of each sensor connector.
Illustration 1 g01242605
Typical schematic
Illustration 2 g01242612
P1 ECM connector
(P1-3) Sensor return (left rail)
(P1-14) "Inlet manifold temperature sensor"
(P1-26) Engine oil temperature sensor
(P1-35) Sensor return (right rail)
Illustration 3 g01163206
Sensor connector
(Terminal 1) Sensor signal
(Terminal 2) Sensor return
Illustration 4 g01234146
Location of ECM connectors
Test Step 1. Check for "Active" or "Logged" Diagnostic Codes
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Restore power to the ECM.
Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes. Note: Wait at least
Parts valve Volvo Penta:
861862
861862 Valve spring washer
D1-13; D1-13B; D1-20, MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
861861
861861 Valve spring
D1-13; D1-13B; D1-20, MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
861860
861860 Valve stem seal
D1-13; D1-13B; D1-20, MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
3840854
3840858
21192977
861864
861864 Valve seat
MD2010-C; MD2010-D; MD2020-C, MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
3581520