832882 Volvo.Penta Valve housing


832882 Valve housing Volvo.Penta AQ115A; AQ115B; AQ130 Valve
832882 Valve housing Volvo Penta
Rating:
38

Buy Valve housing 832882 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Compatible models:

Volvo Penta entire parts catalog list:

AQ115A; AQ115B; AQ130; AQ130A; AQ130B; AQ130C; AQ130D; AQ165A; AQ170A; AQ170B; AQ170C; AQD21A; BB115A; BB115B; BB115C; BB165A; BB170A; BB170B; BB1

Information:

Start By:a. remove piston cooling jets1. Using tool (A), turn the engine flywheel to move the connecting rod cap bolts into a position for removal. 2. Remove bolts (1) and bearing cap (2) from the crankshaft and connecting rod. Remove the lower half of the bearing from caps (2).3. Push the connecting rods away from the crankshaft. Remove the upper halves of the bearing from the rods. Install rod bearings dry when the clearance check are made. Put clean engine oil on the rod bearings for final assembly.
Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap.
4. Clean the surfaces where the bearing halves fit. Install bearing halves (3) in the rods and caps (2).The serviceman must be very careful to use Plastigage, tool (B) correctly. The following points must be remembered:- Make sure that the backs of the bearings and the bores are clean and dry.- Make sure that the bearing locking tabs are properly seated in their slots.- The crankshaft must be free of oil where the Plastigage touches it.- Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.- Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.- Do not turn the crankshaft with the Plastigage installed.- Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.- Remove the Plastigage before reinstalling the cap.When using Plastigage (B), the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specifications range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004") the readings may be low by 0.013 to 0.025 mm (.0005 to .0010"). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider than the other.For complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531. 5. Check the bearing clearance with Plastigage. Install caps (2) on the connecting rods making sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod. Tighten the bolts in the number sequence shown as follows: Bolts (4) and (5) are installed on the same side of the rod cap that has the locating pin. The locating pin must extend 4.0 0.5 mm (.16 .02 in) from the rod cap.a. Put Molylube of Fel-Pro C100 Lubricant on the bolt threads and contact surfaces of the bolt and caps.b. Hand tighten bolts No. 4 and No. 5 to a torque of 90 5 N m (65 4 lb ft).c. Hand tighten bolts No. 6 and No. 7 to a torque of 90 5 N m (65 4 lb ft).d. Hand tighten bolts No. 4 and No. 5 to a torque of 90 5 N m (65 4 lb ft).e. Hand tighten bolts No. 6 and No. 7 to a torque of 90 5 N m (65 4 lb ft).f. Hand tighten each bolt an additional 90° 15°.6. Remove the rod cap, and measure the Plastigage. The rod bearing clearance must be 0.107 to 0.218 mm (.0042 to .0086 in).7. Put Molylube or Fel-Pro C100 Lubricant on the bolt threads and contact surfaces of the bolts and caps before final assembly. Put clean engine oil on both halves of rod bearings. Install caps (2) and tighten the bolts as in Steps 5b through 5e. An impact wrench can be used for the final tighten torque of 90° 5° in Step 5f.End By:a. install piston cooling jets


Parts valve Volvo Penta:

1306630
Valve stem seal
1306630 Valve stem seal
230A; 230B; 250A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, KAD32P; T
809946
Valve spring
809946 Valve spring
AQ115A; AQ115B; AQ130, MD1B; MD2B; AQD2B
3848256
 
3848256 Valve collet
AQ115A; AQ115B; AQ130, MD21B; AQD21B, MD6; MD6A; MD6B
828239
Valve
828239 Valve
AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, MD21B; AQD21B, MD40A; TMD40A; TMD40B
419702
Valve seal
419702 Valve seal
AQ115A; AQ115B; AQ130, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A
419652
Valve guide, intake
419652 Valve guide, intake
230A; 230B; 250A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, MB10A
419694
Valve seat, intake
419694 Valve seat, intake
AQ115A; AQ115B; AQ130
419695
Valve seat, exhaust
419695 Valve seat, exhaust
AQ115A; AQ115B; AQ130
Back to top