861062 Volvo.Penta Valve cover


861062 Valve cover Volvo.Penta 2001; 2001B; 2001AG Valve
861062 Valve cover Volvo Penta
Rating:
53

Buy Valve cover 861062 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$129.99
 

29-09-2022

-: -
Marine Pro Flame Arrestor w/Adapter Mercruiser 7.4L 1998-2000
Flame Arrestor w/ Adapter Mercruiser 7.4L 1998-2000 || Replaces: 861062 || Pro Marine Provides the highest Quality in aftermarket parts for all your Marine needs! || All Instock Products ship within 1 business day of order! || Same Day Shipping on Most orders placed before 12:30PM Est!!
$62.18
 

12-12-2022
1.0[0.45] Pounds
-: -
ANZO USA 861062 LED Magnet Light
Easy to install - || Thermo-Hygrometer (temperature and humidity chamber) and rain-resistant tested || SAE (society of automotive engineers) and D.O.T. (department of transportation) compliant with FMVSS (federal motor vehicle safety standarts) no. 108 || Provides clean and great match for hi-tech Euro style
Number on catalog scheme: 11
 

Compatible models:

2001; 2001B; 2001AG   Volvo.Penta

Volvo Penta entire parts catalog list:

2001; 2001B; 2001AG; 2001BG; 2002; 2002B; 2002D; 2002AG; 2002BG; 2003; 2003B; 2003D; 2003AG; 2003BG; 2003T; 2003TB; 2003 SOLAS; 2003B SOLAS; 2003T

Information:

Start By:a. remove oil pump 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1), which shows the direction of the front of the block, and a number (3) which gives the location of that cap.2. Remove No. 2 through No. 6 main bearing caps from the engine. Remove the lower bearings from the caps.3. Remove the thrust plate from each side of the No. 4 upper main bearing.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly.5. Install lower bearings in the bearing caps.6. Install upper bearings in the cylinder block with tool (A). Be sure tab (5) on the back of the bearings fits in the groove of the caps and cylinder block. When the bearing clearance is checked and the engine is in a vertical position, such as in the vehicle, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, such as on an engine stand, it is not necessary to hold the crankshaft up. Do not turn crankshaft when the Plastigage is in position to check clearance.
Do not use an impact wrench to tighten the bolts the additional 120°.
7. Check the bearing clearance with tool (B) as follows:a. Put 2P2506 Thread Lubricant on the threads of the cap bolts. Install the bearing caps and bolts finger tight.b. Tighten the bolts on the tab end of the caps first to a torque of 260 14 N m (190 10 lb.ft.).c. Tighten the bolts on the other end of the caps to a torque of 260 14 N m (190 10 lb.ft.).d. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. Make sure the main bearing caps are installed with their identification number (3) in alignment with the identification number on the left side of the cylinder block, and arrow (1) toward the front of the block.8. Remove the bearing caps and tool (B).9. Measure the thickness of the Plastigage to find the bearing clearance. The clearance for new bearings must be 0.091 - 0.186 mm (.0036 - .0073 in.). The maximum clearance for used bearings is 0.025 mm (0.010 in.).10. Install a thrust plate (6) on each side of the No. 4 upper bearing. Install the thrust plates with the side marked "Block Side" toward the cylinder block.11. Install No. 2 through 6 main bearing caps. Follow the tightening procedure in Step 7. 12. Do Steps 2, 4 through 9 and 11 for the No. 1 and No. 7 main bearing caps. Check the end play of the crankshaft with tool (C). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.152 - 0.508 mm (0.006 - 0.020 in.). The maximum end play with used thrust plates is 0.89 mm (0.035 in.).End By:a. install oil pump


Parts valve Volvo Penta:

840339
 
840339 Valve cover
2001; 2001B; 2001AG
861063
 
861063 Valve cover
2001; 2001B; 2001AG
858407
 
858407 Valve cover
2001; 2001B; 2001AG
859241
Valve cover
859241 Valve cover
2001; 2001B; 2001AG
861076
Valve cover
861076 Valve cover
2001; 2001B; 2001AG
838081
 
838081 Valve spring
2001; 2001B; 2001AG, MD5A; MD5B; MD5C, MD6; MD6A; MD6B
859610
 
859610 Valve spring washer
2001; 2001B; 2001AG
859171
Valve stem seal
859171 Valve stem seal
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42
Back to top