861076 Volvo.Penta Valve cover


861076 Valve cover Volvo.Penta 2001; 2001B; 2001AG Valve
861076 Valve cover Volvo Penta
Rating:
23

Buy Valve cover 861076 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$79.09
 

05-10-2023
1.4[0.63] Pounds
-: -
KarParts360 ANZO For Dodge Ram 3500 1994-1998 Cab Roof Light LED Clear - 5pc | 861076
ANZO 1994-1998 DG R-A-M 2500 LED Cab Roof Light Kit Smoke 5pc || Part Number: 861076 || LED Cab Lights Smoke 5Pc || Housing Color: Chrome || Factory Sealed - Brand new in box
$77.32
 

18-04-2023
0.75[0.34] Pounds
-: -
ANZO USA 861076 5pc. Smoke Lens LED Cab Roof Light Kit
Anzo USA a trusted industry leader || Backed by manufacturer's Warranty || D.O.T. Compliant To FMVSS No.1454 || Changes The Look Of The Vehicle In 30 Minutes || Simply Plug And Play
$51.17
 

26-07-2018
320 Hundredths Pounds
Bulbrite: Bulbrite
Bulbrite 861076 40 W Dimmable T8 Shape Incandescent Bulb (E26) Base with Medium Screw, 5 Pack, Clear
Included in the box: (5) 40 watt dimmable showcase, aquarium (T8) 2700K||Specifications: 40 watts, 190 lumens, 100 CRI, 2000 hour average rated life, medium screw (E26) base, maximum overall length is 11 inches and bulb diameter is 1 inches||Country of origin is China
Number on catalog scheme: 13
 

Compatible models:

2001; 2001B; 2001AG   Volvo.Penta

Volvo Penta entire parts catalog list:

2001; 2001B; 2001AG; 2001BG; 2002; 2002B; 2002D; 2002AG; 2002BG; 2003; 2003B; 2003D; 2003AG; 2003BG; 2003T; 2003TB; 2003 SOLAS; 2003B SOLAS; 2003T

Information:

1. Remove bolts (1) that hold main bearing caps (2) to the block and remove main bearing caps (2). 2. Install one of the bolts from the front pulley in each end of the crankshaft.3. Fasten a hoist to crankshaft (3) and remove crankshaft (3) from the block. The weight is 159 kg (350 lb). If new main bearings are not to be installed, keep old bearings with identification as to their location in cylinder block. 4. Use tooling (A) to remove the crankshaft gear.5. Use tooling (B) if necessary to remove the dowel and the pin.Install Crankshaft
If the crankshaft journals and bores for the block and rods were measured at disassembly and found to be within specifications, no further checks are necessary. However, if the serviceman still wants to measure the bearing clearances, Plastigage is recommended. Lead wire, shim stock or use of a dial bore gauge can damage the bearing surface.The serviceman must be very careful to use Plastigage, tool (B) correctly. The following points must be remembered:* Make sure that the backs of the bearings and the bores are clean and dry.* Make sure that the bearing locking tabs are properly seated in their slots.* The crankshaft must be free of oil where the Plastigage touches it.* If the main bearing clearances are checked with the engine upright or on its side, the crankshaft must be supported. Use a jack under an adjacent crankshaft counterweight and hold the crankshaft against the crown of the bearing. If the crankshaft is not supported, the weight of the crankshaft will cause incorrect readings.* Put a piece of Plastigage on the crown of the bearing half that is in the cap. Do not allow the Plastigage to extend over the edge of the bearing.* Install the bearing cap using the correct torque-turn specifications. Do not use an impact wrench. Be careful not to dislodge the bearing when the cap is installed.* Do not turn the crankshaft with the Plastigage installed.* Carefully remove the cap but do not remove the Plastigage. Measure the width of the Plastigage while it is in the bearing cap or on the crankshaft journal. Do this by using the correct scale on the package. Record the measurements.* Remove the Plastigage before reinstalling the cap.When using Plastigage, the readings can sometimes be unclear. For example, all parts of the Plastigage are not the same width. Measure the major widths to make sure that they are within the specification range. Also, experience has shown that when checking clearances tighter than 0.10 mm (.004 in) the readings may be low by 0.013 to 0.025 mm (.0005 to .0010 in). Out-of-round journals can give faulty readings. Also, journal taper may be indicated when one end of the Plastigage is wider that the otherFor complete details concerning measuring bearing clearances, see Engine Bearings And Crankshafts, Form No. SEBD0531. 1. Install pin (5) in the crankshaft end until it is extended from the surface 6.4 0.5 mm (.25 .02 in).2. Install dowel (6) until it is extended from the surface 4.1 0.5 mm (.16 .02 in). 3. Heat crankshaft gear (4) to a maximum temperature of 232°C (450°F). Install gear (4) on the crankshaft with the keyaway in alignment with dowel (6) and the "V" mark to the outside. The dowel in the crankshaft must be in alignment with the keyaway in crankshaft gear (4).4. Clean the cylinder block and main bearing caps thoroughly. Install the bearings dry when the clearance checks are made. Put clean engine oil on the bearings for final assembly. 5. Install upper half of main bearings (7) in the block. 6. Install one bolt for the flywheel on each end of the crankshaft.7. Fasten a hoist and put crankshaft (3) in position in block. Be sure the "V" mark on the crankshaft gear is in alignment with "V" mark on the idler gear.8. Install main bearings in bearing caps. Be sure tabs (8) on the back of the bearings fit in the tab slots of the caps and cylinder block.9. Use Plastigage (B) to check bearing clearance.10. Put Plastigage (B) on the bearing.
Be sure main bearing caps (2) are installed so the numbers on the side of the cylinder block are the same as the numbers on the bearing caps and the arrows on the caps are toward the front of the cylinder block.
11. Put 4C5593 Thread Lubricant/Anti-Seize on bolts (1). Install bolts (1) and main bearing caps (2). Starting with the tab and of the bearing cap first, tighten each bolt in the bearing caps to a torque of 260 14 N m (190 10 lb ft). Put a mark on each bolt and bearing cap. Start with the bolt away from (opposite) the tab end of the bearing cap and again tighten each bolt an additional 120° 5°.12. Remove the main bearing caps. Remove Plastigage (B) from the caps. Check the width of Plastigage (B) to find the bearing clearance. The bearing clearance must be 0.091 to 0.185 mm (.0036 to .0073 in) with new bearings. Maximum clearance with used bearings is 0.25 mm (.010 in).13. Install the thrust bearings for No. 4 main bearing. Install the thrust bearings with the side identification "BLOCK SIDE" toward the cylinder block.14. Put 4C5593 Thread Lubricant/Anti-Seize on bolts (1). Install bolts (1) and main bearing caps (2). Starting with the tab end of the bearing cap first, tighten each bolt in the bearing caps to a torque of 260 14 N m (190 10 lb ft). Put a mark on each bolt and bearing cap. Start with the bolt away from (opposite) the tab end of the bearing cap and again tighten each bolt (1) an additional 120° 5°. 15. Check the end play of the crankshaft with tool group (A). Be sure the dial indicator is against a machined surface. The end play is controlled by the thrust bearings of No. 4 (center) main bearing. The


Parts valve Volvo Penta:

861062
Valve cover
861062 Valve cover
2001; 2001B; 2001AG
840339
 
840339 Valve cover
2001; 2001B; 2001AG
861063
 
861063 Valve cover
2001; 2001B; 2001AG
858407
 
858407 Valve cover
2001; 2001B; 2001AG
859241
Valve cover
859241 Valve cover
2001; 2001B; 2001AG
838081
 
838081 Valve spring
2001; 2001B; 2001AG, MD5A; MD5B; MD5C, MD6; MD6A; MD6B
859610
 
859610 Valve spring washer
2001; 2001B; 2001AG
859171
Valve stem seal
859171 Valve stem seal
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42
Back to top