865658 Volvo.Penta Vibration damper


865658 Vibration damper Volvo.Penta TD610G; TWD610G; TD710G Vibration
865658 Vibration damper Volvo Penta
Rating:
53

Buy Vibration damper 865658 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$15.99
 

26-05-2023
1.0 ounces
-: -
Coffee Mug Got Survival Skills Scouting Funny Sayings 865658
PREMIUM QUALITY - High quality white ceramic has our unique design on both sides. Dishwasher and microwave safe. || THE PERFECT GIFT - An awesome present for a grandpa, grandma, father, mother, husband, wife, uncle, aunt, son, daughter, nephew, niece, boyfriend, girlfriend, best friends, sibling, coworker,... Makes a great gift for your loved ones. || GOOD FOR SEVERAL OCCASIONS - A useful gift to coffee lovers for Valentine's Day, Mother's Day, Father's Day, bday gifts, Christmas gifts, inexpensive holiday gift, humorous appreciation gift, your anniversary, gift exchange humor, sarcastic gag gift, retirement, funniest creative small gifts. || SATISFACTION GUARANTEE - If you require any further information, feel free to contact us. Your pleasure is our priority!
Number on catalog scheme: 18
 

Compatible models:

Volvo Penta entire parts catalog list:

TD610G; TWD610G; TD710G; TWD710G; TAD730G; TWD740GE; TAD740GE; TAD741GE

Information:


Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     9S-9082     Engine Turning Tool     1    Start By:
Remove the engine oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01149594
Use Tooling (A) to rotate the crankshaft until the connecting rod is at the bottom center.
Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary.Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod assembly could cause the connecting rod to fracture.
Remove bolts (1) and connecting rod bearing cap (2) from the connecting rod.
Remove the lower half of the connecting rod bearing from the connecting rod bearing cap.
Push the connecting rod away from the crankshaft. Remove the upper half of the connecting rod bearing from the connecting rod.Installation Procedure
Table 2
Required Tools    
Tool    Part Number    Part Description    Qty    
A     9S-9082     Engine Turning Tool     1    
B     8T-3052     Degree Wheel     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Illustration 2 g00998730
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Install a new lower half connecting rod bearing (3) in connecting rod bearing cap (2) .Note: Ensure that bearing locking tab (4) is located in the notch of the connecting rod bearing cap.
Install a new upper half connecting rod bearing in the connecting rod.Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Pull the connecting rod onto the crankshaft.
Illustration 3 g01149651
Position connecting rod bearing cap (2) on the connecting rod.Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side opposite of the piston cooling jet.
Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.
Tighten bolts (1), as follows:
Tighten Bolt (A) and Bolt (C) to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (B) and Bolt (D) to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (B) and Bolt (D) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (B) is not used, place an index mark on each bolt.
Tighten Bolt (A) and Bolt (C) again to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (A) and Bolt (C) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (B) is not used, place an index mark on each bolt.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By: Install the engine oil pump.


Parts vibration Volvo Penta:

3574797
Vibration damper
3574797 Vibration damper
1372, D12D-A MH; D12D-B MH; D12D-C MH, DH10A; DH10A 285; DH10A 360, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE, TAD1240GE; TAD1241GE; TAD1242GE, TAD1340VE; TAD1341VE; TAD1342VE, TAD1341GE; TAD134
3826416
 
3826416 Vibration damper
TD610G; TWD610G; TD710G
3827882
 
3827882 Vibration damper
TD610G; TWD610G; TD710G, TD71A; TID71A; TWD710V
Back to top