467281 Volvo.Penta Washer


467281 Washer Volvo.Penta DH10A; DH10A 285; DH10A 360 Washer
467281 Washer Volvo Penta
Rating:
88

Buy Washer 467281 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$574.96
 

26-11-2023
22.0[9.90] Pounds
-: -
American Shifter 467281 Shifter Kit (C6 16" E Brake Cable Clamp Clevis For E64DA, 1 Pack)
Application: C6 || Shifter Style: Push Button & Side Detent || Shifter Arm Size: 16in Single Bend || Shifter Arm Finish: Chrome || Knob: Billet
Number on catalog scheme: 10
 

Compatible models:

Volvo Penta entire parts catalog list:

DH10A; DH10A 285; DH10A 360; DH10A Rail; THD102KD; THD102KB

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
168-2 168-2 Battery Potential / Power Input #1 : Erratic, Intermittent, or Incorrect This code indicates that the battery circuit to the ECM is intermittent.
168-3 168-3 Battery Potential / Power Input #1 : Voltage Above Normal The ECM detects voltage that is above the acceptable value.
168-4 168-4 Battery Potential / Power Input 1 : Voltage Below Normal The ECM detects voltage that is below the acceptable value.
Follow the troubleshooting procedure to identify the root cause of the fault.
Illustration 1 g03366300
Typical example of the schematic for the electrical power supply circuit
Illustration 2 g03366309
View of the pin locations on the P1 connector for the ignition keyswitch and battery supply circuit
(1) Battery ground
(2) Battery ground
(3) Battery ground
(7) Battery+
(8) Battery+
(9) Battery ground
(10) Battery ground
(15) Battery+
(16) Battery+
(40) Ignition keyswitch
Table 2
Troubleshooting Test Steps Value Results
1. Determine the Diagnostic Code
A. Establish communication between the electronic service tool and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Start the engine. Run the engine until the engine is at normal operating temperature.
C. Observe the "Active Diagnostic" screen on the electronic service tool. Wait at least 30 seconds so that any codes may become active.
Diagnostic code
Result: One of the diagnostic codes listed in Table 1 is active.
Proceed to Test Step 2.
Result: The electronic service tool will not communicate with the ECM.
Repair: Refer to Troubleshooting, "Electronic Service Tool Does Not Communicate".
2. Check the Charging Circuit
A. Check the charging circuit. Refer to Systems Operation, Testing and Adjusting, "Charging System - Test".
Charging circuit
Result: The charging system is OK.
Proceed to Test Step 3.
Result: The charging system is not OK.
Repair: There is a fault in the charging system. Make the necessary repairs.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
3. Load Test the Batteries
A. Use a suitable battery load tester to test the batteries. Refer to Systems Operation, Testing and Adjusting, "Battery - Test" for the correct procedure.
Load test
Result: The batteries pass the load test.
Proceed to Test Step 4.
Result: The batteries do not pass the load test.
Repair: Recharge or replace the faulty batteries.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
4. Inspect Electrical Connectors and Wiring
A. Ensure that the battery disconnect switch is in the CLOSED position.
B. Thoroughly inspect all connectors associated with the electrical power supplies.
C. Check all fuses.
D. Perform a 45 N (10 lb) pull test on each of the wires in the connectors associated with the electrical power supplies.
E. Check all the wiring associated with the electrical power supplies for abrasions and pinch points.
F. Verify that the "System Operating Voltage Configuration" is correctly configured in the Engine ECM configuration parameters.
Damaged wire or connector. Blown fuse.
Result: A damaged wire or damaged connector was found. A blown fuse was found.
Repair: Repair the damaged wire or the damaged connector. Replace all blown fuses.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: The "System Operating Voltage Configuration" is configured incorrectly.
Repair: Program the parameter with the correct system voltage.
Result: A damaged wire or damaged connector was not found. The fuses are OK.
Contact the Dealer Solutions Network (DSN).


Parts washer Volvo Penta:

190509
 
190509 Washer
AQ131A; AQ131B; AQ131C, AQ151A; AQ151B; AQ151C, AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D3-110I-A; D3-110I-B; D3-110I-C, D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-1
955893
 
955893 Washer
2001; 2001B; 2001AG, 230A; 230B; 250A, 430; 430A; 430B, 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.0FLPMDA; 5.8FLPMDA, 5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE, 500; 500A; 501A, 571A,
11978
 
11978 Washer
2001; 2001B; 2001AG, D4-180I-B; D4-180I-C; D4-180I-D, D4-180I-F; D4-225A-F; D4-225I-F, D6-280A-A; D6-280A-B; D6-280A-C, D6-300A-F; D6-300D-F; D6-300I-F, DH10A; DH10A 285; DH10A 360, HS25A; HS25A-B; HS25A-C, MD31A; TMD31A; TMD31B, TAD1030G; TD1010G; T
955897
 
955897 Washer
2001; 2001B; 2001AG, 230A; 230B; 250A, 3.0GSMBYMCE; 3.0GSPBYCCE, 3.0GSMWTR; 3.0GSMWTS; 3.0GSPWTR, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ
955899
 
955899 Washer
2001; 2001B; 2001AG, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ145A; BB145A, D120A; D120AK; TD120A, DH10A; DH10A 285; DH10A 360, MD100A; TMD100A; TMD100AK, MD11; MD11C; MD11D, MD120A; MD120AK; TMD120A, MD1B; MD2B; AQD2B, MD21B; AQD21B, MD40A;
940097
Washer
940097 Washer
230A; 230B; 250A, 251A, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 430; 430A; 430B, 5.7Gi-C; 5.7Gi-CF; 5.7Gi-D, 5.7Gi-E; 5.7Gi-EF; 5.7GiI-E, 5.7GiI-F; 5.7GXiI-G,
470357
Washer
470357 Washer
DH10A; DH10A 285; DH10A 360, TAD1230G; TD1210G; TWD1210G, TAD1230P; TD121GP-87; TWD1210P, TAMD122A; TMD122A; TAMD122P-A, TD100CHC; TD100CRC; TD121CHC, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TD120HP-86; TD121; TD121G, TD120HPP;
3090706
Washer
3090706 Washer
DH10A; DH10A 285; DH10A 360
Back to top