21235313 Volvo.Penta Wiring harness

Troubleshooting
Troubleshooting can be difficult. On the following pages there is a list of possible problems. To make a repair to a problem, make reference to the cause and correction.This list of problems, causes, and corrections, will only give an indication of where a possible problem can be, and what repairs are needed. Normally, more or other repair work is needed beyond the recommendations in the list. Remember that a problem is not normally caused only by one part, but by the relation of one part with other parts. This list can not give all possible problems and corrections. The serviceman must find the problem and its source, then make the necessary repairs.1. Engine Will Not Start.2. Misfiring or Running Rough.3. Stall at Low rpm.4. Sudden Changes in Engine rpm.5. Not Enough Power.6. Too Much Vibration.7. Loud Combustion Noise.8. Loud Noise (Clicking) From Valve Compartment.9. Oil in Cooling System.10. Mechanical Noise (Knock) in Engine.11. Fuel Consumption Too High.12. Loud Noise From Valves or Valve Drive Components.13. Little Movement of Rocker Arm and Too Much Valve Clearance.14. Valve Spring Lock is Free.15. Oil at the Exhaust.16. Little or No Valve Clearance.17. Engine Has Early Wear.18. Coolant in Lubrication Oil.19. Too Much Black or Gray Smoke.20. Too Much White or Blue Smoke.21. Engine Has Low Oil Pressure.22. Engine Uses Too Much Lubrication Oil.23. Engine Coolant is Too Hot.24. Starting Motor Does Not Turn.25. Alternator Gives No Charge.26. Alternator Charge Rate is Low or Not Regular.27. Alternator Charge Too High.28. Alternator Has Noise.29. Exhaust Temperature is Too High.Engine Will Not Start Misfiring Or Running Rough Stall At Low RPM Sudden Changes In Engine RPM Not Enough Power Too Much Vibration Loud Combustion Noise (Sound) Loud Noise (Clicking) From Valve Compartment Oil In Cooling System Mechanical Noise (Knock) In Engine Fuel Consumption Too High Loud Noise From Valves Or Valve Drive Components Little Movement Of Rocker Arm And Too Much Valve Clearance Valve Spring Lock Is Free Oil At The Exhaust Little Or No Valve Clearance Engine Has Early Wear Coolant In Lubrication Oil Too Much Black Or Gray Smoke Too Much White Or Blue Smoke Engine Has Low Oil Pressure Engine Uses Too Much Lubrication Oil Engine Coolant Is Too Hot Starting Motor Does Not Turn Alternator Gives No Charge Alternator Charge Rate Is Low Or Not Regular Alternator Charge Too High Alternator Has Noise Exhaust Temperature Is Too High Fuel System
Either too much fuel or not enough fuel for combustion can be the cause of a problem in the fuel system.Many times work is done on the fuel system when the problem is really with some other part of the engine. The source of the problem is difficult to find, especially when smoke comes from the exhaust. Smoke that comes from the exhaust can be caused by a bad fuel injection valve, but it can also be caused by one or more of the reasons that follow: a. Not enough air for good combustion.b. An overload at high altitude.c. Oil leakage into combustion chamber.d. Not enough compression.Fuel System Inspection
A problem with the components that send fuel to the engine can cause low fuel pressure. This can decrease engine performance.1. Check the fuel level in the fuel tank. Look at the cap for the fuel tank to make sure the vent is not filled with dirt.2. Check the fuel lines for fuel leakage. Be sure the fuel supply line does not have a restriction or a bad bend.3. Install a new fuel filter. Clean the fuel screen located in the inlet valve of the fuel transfer pump.4. Remove any air that may be in the fuel system. If there is air in the fuel system, use the priming pump and loosen the nuts holding the fuel lines to the outside of the cylinder head, one at a time. Do this until fuel, without air, comes from the fuel line connection.Check Engine Cylinders Separately
An easy check can be made to find the cylinder that runs rough (misfires) and causes black smoke to come out of the exhaust pipe.Run the engine at the speed that is the roughest. Loosen the fuel line nut at a fuel injection pump. This will stop the flow of fuel to that cylinder. Do this for each cylinder until a loosened fuel line is found that makes no difference in engine performance. Be sure to tighten each fuel line nut after the test before the next fuel line nut is loosened. Check each cylinder by this method. When a cylinder is found where the loosened fuel line nut does not make a difference in engine performance, test the injection pump and fuel injection nozzle for that cylinder.Temperature of an exhaust manifold port, when the engine runs at low idle speed, can also be an indication of the condition of a fuel injection nozzle. Low temperature at an exhaust manifold port is an indication of no fuel to the cylinder. This can possibly be an indication of a nozzle with a defect. Extra high temperature at an exhaust manifold port can be an indication of too much fuel to the cylinder, also caused by a nozzle with a defect.The most common defects found with the fuel injection valves are:1. Carbon on tip of the nozzle or in the nozzle orifice.2. Orifice wear.
Do not test or disassemble nozzles unless you have the correct service tools.
Do not disassemble fuel nozzles before they have been tested. See TESTING PENCIL-TYPE FUEL INJECTION NOZZLES for the nozzle that is installed in your engine.Testing 9N3979 Pencil-Type Fuel Injection Nozzles
*5P4150 Nozzle Testing Group.5P4244 Adapter.8S2270 Fuel Collector.FT1384 Extension.8S2245 Cleaning Tool Group. 8S2258 Brass Wire Brush.8S2250 Nozzle Holding Tool.8S2252 Carbon Seal Installation Tool.1F1153 Needle Nose Pliers.8H8505 Combination Wrench.8H8502 Combination Wrench.8S2274 Socket.8S1589 Socket.9S5031 Socket.5P4813 Socket.5/64" Hex Wrench.*Special Instruction Form No. SEHS7292.
5P4150 NOZZLE TESTING GROUP
A. 5P4721 Tube. B. 5P4146 Gauge, 0 to 1000 p