21895099 Volvo.Penta Wiring harness


21895099 Wiring harness Volvo.Penta 1372, TAD1170VE; TAD1171VE; TAD1172VE, TAD1371VE; TAD1372VE; TAD1373VE, TAD1670VE; TAD1671VE; TAD1672VE, TWD1672GE; TWD1673GE; TWD1672-1673GE Wiring
21895099 Wiring harness Volvo Penta
Rating:
93

Buy Wiring harness 21895099 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Volvo Penta entire parts catalog list:

1372
TAD1170VE; TAD1171VE; TAD1172VE; TAD1170-72VE
TAD1371VE; TAD1372VE; TAD1373VE; TAD1374VE; TAD1375VE; TAD1371-75VE
TAD1670VE; TAD1671VE; TAD1672VE; TAD1670-72VE
TWD1672GE; TWD1673GE; TWD1672-1673GE

Information:


Table 1
Event Code    
Description    Default Conditions which Generate this Code    System Response    
E552(1) Low Aftercooler Coolant Level     The coolant level sensor or the SCAC level sensor sends a signal to the engines' Electronic Control module (ECM) that indicates a low coolant level.     The code is logged.    
E552(2) Low Aftercooler Coolant Level     The coolant level sensor or the SCAC level sensor sends a signal to the engines' ECM that indicates a low coolant level.     The code is logged.
The engine will be derated.    
E552(3) Low Aftercooler Coolant Level     The coolant level sensor or the SCAC level sensor sends a signal to the engines' ECM that indicates a low coolant level.     The code is logged.
The engine will be shutdown.    
E2143(1) Low Engine Coolant Level     The coolant level sensor or the SCAC level sensor sends a signal to the engines' ECM that indicates a low coolant level.     The code is logged.    The coolant level sensor monitors the engine coolant level in order to warn the operator in the event that the coolant level is low. The coolant level sensor is located on the side of the expansion tank.
Illustration 1 g01150024
Coolant level sensor (1) Sensor (2) Sensor probe (brass dowel) (3) Plastic coverCoolant level sensor (1) contains no moving parts. The sensor provides the same function as a switch. The state of the switch is dependent on the capacitance value that is detected. The sensor contains a probe (2) that is covered with plastic (3) .When the probe is not immersed in coolant, the capacitance value changes. The change in the capacitance value is detected by the sensor's electronic circuits. The sensor sources approximately +5 VDC to the signal wire. The ECM detects the voltage and the ECM activates the event code.The event code is probably caused by a low coolant level. The next likely cause is a problem with a wiring harness or with the sensor. The least likely cause is a problem with the ECM.Note: Before continuing with this procedure, verify that the coolant level is acceptable.
Illustration 2 g01444616
Schematic for coolant level sensor
Illustration 3 g01444609
Location of the ECM connectors (4) J2/P2 ECM connectors (5) J1/P1 ECM connectors
Illustration 4 g01443140
P1 ECM connector (P1-15) SCAC coolant level sensor (P1-30) Engine coolant level sensor
Illustration 5 g01443143
P2 ECM connector (P2-57) +8 V digital supply (P2-65) +8 V digital supply (P2-66) Digital sensor return
Pressurized System: Hot coolant can cause serious burns. To open the cooling system filler cap, stop the engine and wait until the cooling system components are cool. Loosen the cooling system pressure cap slowly in order to relieve the pressure.
Test Step 1. Inspect the Electrical Connectors and the Wiring
Turn the Engine Control Switch (ECS) to the OFF/RESET position. Turn the main disconnect switch to the OFF position.
Thoroughly inspect the J1/P1 ECM connector and the J2/P2 ECM connector. Inspect all of the connectors that are associated with the circuit.Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the allen head screw on each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and for pinch points.Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The connectors and wiring are OK. Proceed to Test Step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the connectors and/or wiring or replace the connectors and/or wiring.STOPTest Step 2. Check the Supply Voltage at the Sensor Connector
Disconnect the coolant level sensor.
Turn the main disconnect switch to the ON position. Turn the ECS to the STOP position.
Illustration 6 g01356605
Harness connector for the coolant level sensor (A) +8 VDC (B) Return (C) Signal
Measure the voltage between terminals A (+8 VDC) and B (return) at the harness connector for the coolant level sensor.
Turn the ECS to the OFF/RESET mode. Turn the main disconnect switch to the OFF position.Expected Result:The voltage measurement is 8.0 0.4 VDC.Results:
OK - The voltage measurement is 8.0 0.4 VDC. The supply voltage is reaching the sensor. Proceed to Test Step 3.
Not OK - The voltage measurement is not 8.0 0.4 VDC. The digital sensor supply voltage is not reaching the sensor. Proceed to Test Step 8.Test Step 3. Disconnect the Coolant Level Sensor and Monitor the Status of "Coolant Level"
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Disconnect the connector for the coolant level sensor.
Turn the main disconnect switch to the ON position. Turn the ECS to the STOP position.


Parts wiring Volvo Penta:

872679
 
872679 Wiring harness
1372, 430; 430A; 430B, 5.0GXiCE-J; 5.0GXiCE-JF; 5.0GXiCE-M, 5.0GXiE-JF; 5.0GXiE-J; 5.0OSiE-JF, 5.7GiCE-300-J; 5.7GiCE-300-JF; 5.7GXiCE-J, 5.7GiE-300-J; 5.7GiE-300-JF; 5.7GXiE-J, 8.1GiCE-J; 8.1GiCE-JF; 8.1GiCE-M, 8.1GiE-JF; 8.1GiE-J; 8.1OSiE-JF, 8.1IP
21895101
 
21895101 Wiring harness
1372, TAD1170VE; TAD1171VE; TAD1172VE, TAD1371VE; TAD1372VE; TAD1373VE, TAD1670VE; TAD1671VE; TAD1672VE, TWD1672GE; TWD1673GE; TWD1672-1673GE
21939133
 
21939133 Wiring harness, extension cable
1372, TAD1170VE; TAD1171VE; TAD1172VE, TAD1371VE; TAD1372VE; TAD1373VE, TAD1670VE; TAD1671VE; TAD1672VE, TAD570VE; TAD571VE; TAD572VE, TAD870VE; TAD871VE; TAD872VE, TWD1672GE; TWD1673GE; TWD1672-1673GE
21939134
 
21939134 Wiring harness, extension cable
1372, TAD1170VE; TAD1171VE; TAD1172VE, TAD1371VE; TAD1372VE; TAD1373VE, TAD1670VE; TAD1671VE; TAD1672VE, TAD570VE; TAD571VE; TAD572VE, TAD870VE; TAD871VE; TAD872VE, TWD1672GE; TWD1673GE; TWD1672-1673GE
22088731
 
22088731 Wiring harness
1372, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE, TAD1351VE; TAD1352VE; TAD1353VE, TAD1352VE, TAD1371VE; TAD1372VE; TAD1373VE, TAD1643VE-B, TAD1650VE-B; TAD1650VE-B/51VE; TAD1651VE, TAD1670VE; TA
22071229
 
22071229 Wiring harness
TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE, TAD1643VE-B, TAD1650VE-B; TAD1650VE-B/51VE; TAD1651VE, TAD1670VE; TAD1671VE; TAD1672VE, TWD1672GE; TWD1673GE; TWD1672-1673GE
23074672
 
23074672 Wiring harness
TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE, TAD1351VE; TAD1352VE; TAD1353VE, TAD1371VE; TAD1372VE; TAD1373VE, TAD1643VE-B, TAD1650VE-B; TAD1650VE-B/51VE; TAD1651VE, TAD1670VE; TAD1671VE; TAD1672V
22179192
 
22179192 Wiring harness
TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE
Back to top