88807A16 CABLE ASSEMBLY (BLACK) Force
H090312RD, H090412SD, H120412RD, H120412SD
CABLE
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Force entire parts catalog list:
- POWER TRIM COMPONENTS » 88807A16
- POWER TRIM COMPONENTS(DESIGN I) » 88807A16
- POWER TRIM COMPONENTS » 88807A16
- POWER TRIM COMPONENTS(DESIGN I) » 88807A16
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4030 Thread Lock Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01784893
Typical example
Ensure that the turbocharger is clean and free from damage. Inspect the turbocharger for wear. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If the turbocharger is worn, the complete turbocharger must be replaced.
Test wastegate actuator (20) for correct operation. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect". If the wastegate actuator is damaged or the wastegate actuator does not operate within the specified limits, the complete turbocharger must be replaced.
Illustration 2 g01782773
Clean the gasket surfaces of the exhaust manifold (1). If necessary, install studs (18) to the exhaust manifold. Tighten the studs to a torque of 18 N m (13 lb ft). Note: Support the exhaust manifold during installation of the turbocharger.
Install a new gasket (16) to exhaust manifold (1).
Position turbocharger (13) on exhaust manifold (1).
Install nuts (14). Tighten the nuts to a torque of 44 N m (32 lb ft).
Ensure that tube assembly (6) is clean and free from damage. Replace any damaged components.
Position a new gasket (15) and bolts (17) onto tube assembly (6).
Install tube assembly (6) to turbocharger (13). Tighten bolts (17) finger tight.
Install exhaust manifold (1) and the assembly of the turbocharger to the cylinder head. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install" for the correct procedure.
Remove the plug from oil inlet port (19). Refer to Illustration 1. Lubricate the turbocharger bearings with clean engine oil through the oil inlet port. Rotate the wheel of the compressor several times in order to lubricate the bearings.
Ensure that tube assembly (2) is clean and free from damage. Replace any damaged components.
Install banjo bolt (11) and new sealing washers (12) to tube assembly (2).
Illustration 3 g01780893
Install banjo bolt (7) and new sealing washers (9) to tube assembly (2).
Install tube assembly (2) to turbocharger (13). Tighten banjo bolt (11) finger tight. Refer to Illustration 2.
Tighten banjo bolt (7) to the cylinder block finger tight.
Position a new gasket (8) between the flange of tube assembly (6) and the cylinder block. Install bolts (10) finger tight.
Tighten banjo bolt (7) to a torque of 20 N m (14 lb ft). Tighten bolts (10) to a torque of 22 N m (16 lb ft).
Tighten banjo bolt (11) to a torque of 20 N m (14 lb ft). Tighten bolts (17) to a torque of 9 N m (80 lb in). Refer to Illustration 2.
Install bolt (3) for the tube clip to the cylinder block. Tighten bolt (3) to a torque of 44 N m (32 lb ft).
Install bolt (5) and spacer (4) for the tube clip to the cylinder block. Tighten bolt (5) to a torque of 44 N m (32 lb ft).
If the turbocharger has an exhaust elbow, install the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install".
Connect the exhaust pipe.
If the turbocharger has a remote wastegate solenoid, connect the hose to the actuator on the turbocharger. Connect the hose assembly for the wastegate solenoid to the tube assembly for the oil feed on the turbocharger. The hose assembly is secured with clips.
Connect the air outlet hose to turbocharger (13). If the engine has an air pipe, install the air pipe and install the gasket to the cylinder head. Apply Tooling (A) to the fasteners for the air pipe. Tighten the fasteners to a torque of 22 N m (16 lb ft).Tighten the hose clamps to a torque of 5 N m (44 lb in).Note: If the air outlet hose has a reflective heat shield, ensure that the reflective heat shield is installed toward the engine.
Connect the air inlet hose to turbocharger (13).
Parts cable Force:
56762
56762 CABLE TIE (4")
H005201RS, H005201SD, H005201TS, H005201UD, H0052C88A, H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201T
816311
816311 CABLE TIE (8")
H0091H84D, H009201RS, H009201SD, H009201UD, H009201US, H0092284D, H0092H84L, H0092S88A, H0092S91A, H0093S91A, H015201RS, H015201US, H015211SS, H0152C84K, H0152S89A, H025201RD, H025201TD, H025201TS, H025201US, H040312RD, H040312SD, H040312UD, H0407E92
88807A29
88807A29 CABLE ASSEMBLY (Black)
H040312RD, H0407E92C, H0706A91B, H090312RD, H0903E91D, H0903E91H, H090LD90B, H090LD91D, H1201A90A, H120412RD, H120LD91B, H120LD91D, H120LD92B, H1501E89A
821945A28
821945A28 CABLE ASSEMBLY-Hi Tension
H040312RD, H0407E92C, H0706A91B, H090312RD, H0903E91H, H1201A90A, H120412RD, H1501E89A
825275A 1
17201A 2
87379A14
87379A46