F2075 Force SLOTTED HD SCREW, S.S., 1/4 - 20 X 2 1/2


F2075 SLOTTED HD SCREW, S.S., 1/4 - 20 X 2 1/2 Force H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0559H80N, H0559H83R, H0606H84A, H0659B78B SLOTTED
F2075 SLOTTED HD SCREW, S.S., 1/4 - 20 X 2 1/2 Force
Rating:
13

Buy SLOTTED HD SCREW, S.S., 1/4 - 20 X 2 1/2 F2075 Force genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Force entire parts catalog list:

H0558H79L 1979
H0559B80M 1980
H0559H77H 1977
H0559H77J 1977
H0559H78K 1978
H0559H80N 1980,1981
H0559H83R 1983
H0606H84A 1984,1985,1989
H0659B78B 1978

Information:


Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not drain the engine lubricating oil when the engine is cold. As the engine lubricating oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed with draining cold oil. Drain the oil pan with the engine stopped. Drain the oil pan with the oil warm. This draining method allows the waste particles that are suspended in the oil to be drained properly.Failure to follow this recommended procedure will cause the waste particles to be recirculated through the engine lubrication system with the new oil.Drain the Engine Lubricating Oil
Note: Ensure that the vessel that will be used is large enough to collect the waste oil.After the engine has been run at the normal operating temperature, stop the engine. Use one of the following methods to drain the engine oil pan:
Illustration 1 g01430582
Typical example
If the engine is equipped with a drain valve, turn the drain valve knob counterclockwise in order to drain the oil. After the oil has drained, turn the drain valve knob clockwise in order to close the drain valve.
If the engine is not equipped with a drain valve, remove the oil drain plug (1) in order to allow the oil to drain. If the engine is equipped with a shallow oil pan, remove the bottom oil drain plugs from both ends of the oil pan.After the oil has drained, the oil drain plugs should be cleaned and installed. If necessary, replace the O ring seal. Tighten the drain plug to 34 N m (25 lb ft).Replace the Oil Filter
Caterpillar oil filters are manufactured to Caterpillar specifications. Use of an oil filter that is not recommended by Caterpillar could result in severe damage to the engine bearings, crankshaft, etc., as a result of the larger waste particles from unfiltered oil entering the engine lubricating system. Only use oil filters recommended by Caterpillar.
Remove the oil filter with a 1U-8760 Chain Wrench. Note: Some oil filters may be installed horizontally. This type of oil filter can be drained before the filter is removed. The torque for this drain plug is 12 N m (8 lb ft).Note: The following actions can be carried out as part of the preventive maintenance program.
Illustration 2 g00588944
Element with debris
Cut the oil filter open with a 175-7546 Oil Filter Cutter . Break apart the pleats and inspect the oil filter for metal debris. An excessive amount of metal debris in the oil filter may indicate early wear or a pending failure. Use a magnet to differentiate between the ferrous metals and the nonferrous metals that are found in the oil filter element. Ferrous metals may indicate wear on the steel and cast iron parts of the engine.Nonferrous metals may indicate wear on the aluminum parts, brass parts or bronze parts of the engine. Parts that may be affected include the following items: main bearings, rod bearings, turbocharger bearings and cylinder heads.Due to normal wear and friction, it is not uncommon to find small amounts of debris in the oil filter. Consult your Caterpillar dealer in order to arrange for a further analysis if an excessive amount of debris is found in the oil filter.
Illustration 3 g01187802
Typical example
Clean the sealing surface of the oil filter head (2). Ensure that the union is secure in the filter head.
Apply clean engine oil to the O ring seal (3) for the new oil filter. Note: Some oil filters may be installed horizontally. Refer to the illustration . This type of oil filter assembly can be drained before the filter is removed. The torque for this drain plug (4) is 12 N m (8 lb ft). If necessary, install a new O ring seal (5). Start at step 1 in order to remove the oil filter and install the oil filter.
Do not fill the oil filters with oil before installing them. This oil would not be filtered and could be contaminated. Contaminated oil can cause accelerated wear to engine components.
Horizontal Oil Filter
Illustration 4 g01430585
Typical example
Note: Some oil filters may be installed horizontally. Refer to illustration 4. This type of oil filter assembly can be drained before the filter is removed. Start at step 1 in order to remove the oil filter and install the oil filter.Fill the Oil Pan
Remove the oil filler cap. Refer to this Operation and Maintenance Manual, "Fluid Recommendations" for more information on suitable oils. Fill the oil pan with the correct amount of new engine lubricating oil. Refer to this Operation and Maintenance Manual, "Refill Capacities" for more information on refill capacities.


Parts slotted Force:

F1860
 
F1860 SLOTTED BINDING HD SCREW, 6 - 32 X 1/4
H0202B80L, H0202B81M, H0202H79K, H0202H82N, H0252B83G, H0252H77B, H0252H78C, H0252H78D, H0254H75A, H0257F88A, H0257F88B, H0306B80C, H0307H81D, H0350H78L, H0351H76K, H0352F90B, H0352F90C, H0352H77H, H0352H79L, H0353E91A, H0353E91B, H0353H78K, H0353H80
F1648
 
F1648 SLOTTED PAN HD SCREW, 10 - 24 X 3/4
H0091B80B, H0091H79A, H0091H83C, H0091H84D, H0092H79F, H0092H81H, H0092H81J, H0095B80F, H0095B81G, H0095H82H, H0101B78A, H0102H76C, H0102H78E, H0121B79A, H0122H79E, H0125H79E, H0152B78D, H0152B83J, H0152C84K, H0152H79E, H0202B81M, H0202H79K, H0252B83
F1979
 
F1979 SLOTTED PAN HD SCREW, 10 - 24 X 3/4
H0042081C, H0042082D, H0042083E, H0042B78C, H0042C84L, H0042C87A, H0042H77B, H0042H78D, H0042H78E, H0042H79F, H0043F85A, H0054H76D, H0091H79A, H0091H83C, H0091H84D, H0092H81H, H0092H81J, H0092H83K, H0092H84L, H0095B80F, H0095B81G, H0095H82H, H0101B78
F2077
 
F2077 SLOTTED PAN HD M. SCREW, 10 - 32 X 1/4
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0659B78B, H1059H76D
F1036
 
F1036 SLOTTED FILL HD M. SCREW, 6 - 32 X 1/4
H0558H79L, H0559B80M, H0559H77H, H0559H77J, H0559H78K, H0659B78B, H1059H76D
F1306
 
F1306 SLOTTED ROUND HD SCREW, 10 - 24 X 3/8
H0559H77H, H0559H77J, H0559H78K
F1038
 
F1038 SLOTTED PAN HD. SCREW 1/4 - 20 X 3/4
H0559H80N, H0559H83R, H0606H84A, H0856H82K, H0858C84H, H0906R83D, H1158H84G, H1258H81A
F1550
 
F1550 SLOTTED PAN HD. SCREW #12 - 24 X 1
H0559H80N, H0559H83R, H0606H84A, H0851X88A, H0853F88B, H0856C87A, H0856C87B, H0856F84A, H0856F85A, H0856F86A, H0856H82K, H0858C84H, H0906R83D, H1158H84G, H1251A88A, H1251A88B, H1251A88C, H1251A89A, H1251A89B, H1251A89C, H1251A89D, H1251A89E, H1251F84
Back to top