0394593 THROTTLE LEVER, Lower JOHNSON
BJ250CXECB, BJ250CXEDA, BJ250CXEUM, CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, J250CXARC, J250CXATF, J250CXEIE, J250CXEND, J250CXEOR, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXEIE, J300CXEND, J300CXEOR, J300CXERC, J300CXESB, J
THROTTLE
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- THROTTLE LINKAGE » 0394593
BJ250CXEUM, BJ250TXEUM 1997
CJ275TLCDC, CJ275TXCDC, J275PTLCDC, J275PTXCDC 1986
CJ275TLCOS, CJ275TXCOS, J275TLCOS, J275TXCOS 1985
CJ300TLCDC, CJ300TXCDC, J300TLCDC, J300TXCDC 1986
CJ300TLCOS, CJ300TXCOS, J300TLCOS, J300TXCOS 1985
J250CXARC, J250CXERC, J250CZERC, J250TXARC, J250TXERC, J250TZERC 1994
J250CXATF, J250CXATS, J250CXETF, J250CXETS, J250CZATF, J250CZATS, J250CZETF, J250CZETS, J250TXATF, J250TXATS, J250TXETF, J250TXETS, J250TZATF, J250TZATS, J250TZETF, J250TZETS 1993
J250CXEIE, J250TXEIE 1991
J250CXEND, J250CZEND, J250TXEND, J250TZEND 1992
J250CXEOR, J250CZEOR, J250TXEOR, J250TZEOR 1995
J275CLCUR, J275CXCUR, J275PLCUR, J275PXCUR 1987
J275CXCCA, J275PLCCA, J275PXCCA 1988
J300CLCUR, J300CXCUR, J300PLCUR, J300PXCUR 1987
J300CXCCA, J300PLCCA, J300PXCCA 1988
J300CXCEM, J300PLCEM, J300PXCEM 1989
J300CXEIE, J300PLEIE, J300PXEIE 1991
J300CXEND, J300PLEND, J300PXEND 1992
J300CXEOR, J300PLEOR, J300PXEOR 1995
J300CXERC, J300PLERC, J300PXERC 1994
J300CXESB, J300PLESB, J300PXESB 1990
J300CXETF, J300CXETS, J300PLETF, J300PLETS, J300PXETF, J300PXETS 1993
Information:
Table 1
Diagnostic Codes Table    
Code and Description    Conditions which Generate this Code    System Response    
168-0 Electrical System Voltage high - most severe (3)     The battery supply voltage is greater than 32 VDC for 0.5 seconds.
The engine's ECM has been powered for 3 seconds.
The engine has been running for at least 30 seconds.     The code is logged.    
168-1 Electrical System Voltage low - most severe (3)     The battery supply voltage is less than 9 VDC for 0.5 seconds.
The engine's ECM has been powered for 3 seconds.
The engine is running for at least 3 seconds.    
168-2 Electrical System Voltage erratic, intermittent, or incorrect     The battery voltage falls below 6 VDC and the voltage returns above 9 VDC for three voltage readings in the last 7 seconds.
The engine is running.    Unswitched battery voltage is supplied to the ECM at P1-48, P1-52, and P1-53. The negative battery is supplied to the ECM at P1-61, P1-63, and P1-65. The ECM receives the input from the keyswitch at P1-70 when the keyswitch is in the ON position or in the START position. When the ECM detects battery voltage at this input, the ECM will power up. When battery voltage is removed from this input, the ECM will power down. The ECM continuously receives battery voltage through the circuit breaker for the ECM.The ECM requires the keyswitch to be in the ON position in order to maintain communications with Caterpillar Electronic Technician (ET).
Illustration 1 g01368963
Schematic for the electrical power supply circuit
Illustration 2 g01364991
Location of the connectors that are for the electrical power supply circuit (typical left side engine view) (1) Engine interface connector (2) J1/P1 ECM connectors
Illustration 3 g01341802
Terminal locations at the P1 ECM connectors for the electrical power supply circuit (P1-48) +Battery (P1-52) +Battery (P1-53) +Battery (P1-61) −Battery (P1-63) −Battery (P1-65) −Battery (P1-70) Keyswitch
Table 2
Troubleshooting Test Steps     Values     Results    
1. Inspect the Electrical Connectors and the Wiring
A. Remove electrical power from the engine ECM.
B. Thoroughly inspect connectors (1) and (2). Inspect all of the connectors that are in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a
45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
D. Check the allen head screw for each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
E. Check the harness and the wiring for abrasion and for pinch points.    
All connectors, pins, and sockets are inserted and coupled completely. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections are tight and free of corrosion.    
Result: The harness and wiring appear to be OK.
Proceed to Test Step 2.
Result: There is a problem in the connectors and/or wiring.
Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are coupled completely. Verify that the repair eliminates the problem.    
2. Check the Battery Voltage at the ECM
A. Remove electrical power from the ECM.
B. Disconnect the J1/P1 ECM connector.
C. Restore electrical power to the ECM.
D. Turn the keyswitch to the ON position.
E. Wiggle the wires in the harness while performing the following test steps.
a. Measure the voltage between P1-48 (+Battery) and P1-61 (−Battery).
b. Measure the voltage between P1-52 (+Battery) and P1-63 (−Battery).
c. Measure the voltage between P1-53 (unswitched +Battery) and P1-65 (−Battery).
d. Measure the voltage between P1-70 (keyswitch) and P1-63 (−Battery).    
The measured voltage is between 22 VDC and 27 VDC.    
Result: The ECM is receiving the correct voltage.
There may be an intermittent electrical problem in a harness or in a connector. If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".
Battery voltage out of range - The voltage is not correct for one of the battery circuits at the ECM.
Proceed to Test Step 3.
Keyswitch voltage out of range - The voltage is not correct for the keyswitch circuit at the ECM.
Proceed to Test Step 4.    
3. Check the Batteries
A. Measure the no-load battery voltage at the battery posts.
B. Load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure".
   
The batteries pass the load test.    
Result: The batteries pass the load test.
The batteries are OK. There is an open circuit or excessive resistance in the wiring or connections between the batteries and the ECM. Verify that the 20 Amp circuit breaker for the ECM is not tripped. Verify that the connections at the bus bars that are for the battery are clean and tight. Repair the connectors or wiring and/or replace the connectors or wiring between the battery and the J1/P1 ECM connector.
Result: The battery voltage is low or the battery did not pass the load test.
Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.    
4. Check the Voltage from the Keyswitch to the ECM
A. Remove electrical power from the ECM.
B. Remove the wire from the terminal R of the keyswitch.
C. Restore electrical power to the ECM.
D. Turn the keyswitch to the ON position.
E. Measure the voltage on terminal B of the keyswitch to the negative battery contact.
F. Measure the voltage on terminal R of the keyswitch to the negative battery contact.
G. Remove electrical power from the ECM.
H. Turn the keyswitch to the OFF position.    
Voltage is present on terminal B and terminal R at the keyswitch.    
Result: Voltage is present on terminal B and terminal R at the keyswitch.
There is a problem in the circuit that
Parts throttle JOHNSON:
0394032
0394032 THROTTLE LEVER ASSY.
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, D100WTLM, HJ55WMLM, HJ55WMLZ, J100STLCCA, J100STLCEM, J100STLESB, J100WMLCDR, J100WMLCOC, J100WMLCRS, J100WTLCUA, J100WTLESM, J100WTLZ, J10EESC, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115MLCOS, J1
0329751
0329751 THROTTLE CAM
CJ275TLCOS, CJ300TLCOS, J120TLCCA, J120TLCDC, J120TLCOS, J120TLCUR, J140CXCCS, J140TLCDC, J140TLCOS, J140TLCUA
0397577
0397579
0394592
0333094
0333094 THROTTLE CAM
BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ250CXECB, BJ250CXEDA, BJ250CXEUM, CJ275TLCDC, CJ300TLCDC, J120TLAEM, J120TLAIE, J120TLAND, J120TLARC, J120TLASB, J120TLATF, J120TLCCA, J120TLCDC, J120TLCUR, J125ESXENR, J125ESX
0396714
0396714 THROTTLE LEVER, Upper
BJ200CXEDR, BJ200CXEEB, BJ200CXSSE, BJ200PLSIF, BJ225CXEEC, BJ225CXSSR, BJ225PLSIF, BJ250CXECB, BJ250CXEDA, BJ250CXEUM, CJ275TLCDC, CJ300TLCDC, J185ESERK, J185ESXENR, J185ESXESS, J185ESXETA, J185ESXW, J200CXARC, J200CXATF, J200CXCCR, J200CXCEA, J200C
0397581
0397581 THROTTLE BODY ASSY.
CJ275TLCDC, CJ300TLCDC, J250CXARC, J250CXATF, J250CXEIE, J250CXEND, J250CXEOR, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM, J300CXEIE, J300CXEND, J300CXEOR, J300CXERC, J300CXESB, J300CXETF